LEMON Manuals: Even more car manuals for everyone
Home >> Porsche >> 2016 >> Macan S >> Repair and Diagnosis >> External Pages >> Different car >> Section 304 (2X - Petrol, Exhaust, Engine-Electronic - General -- 911 CARRERA (991)) >> WM 2X00IN Technical Values - Gt3 (Gt3, Gt3 RS) >> Technical Values

Technical Values

WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2019 Porsche 911, 2018 Porsche 911, 2017 Porsche 911, 2016 Porsche 911, and 2015 Porsche 911. However, it is still accessible from the selected car via links, so may be relevant.
Location Description Type Basic value Tolerance 1 Tolerance 2
Fuel tank to body Screw, M8 x 40 Tightening torque 23 Nm (17 ftlb.)    
Filler neck to body Screw, M6 Tightening torque 10 Nm (7.5 ftlb.)    
Carbon canister to body M6 Tightening torque 10 Nm (7.5 ftlb.)    
Fuel pump control unit to battery console Hexagon speed nut Tightening torque 2.5 Nm (2 ftlb.)    
Intake-air distributor to cylinder head External Torx screw, M6 x 35 Tightening torque 13 Nm (9.5 ftlb.)    
Clamp securing resonance tube External Torx screw, M6 x 30 Tightening torque 3 Nm (2 ftlb.)    
Line bracket to intake-air distributor External Torx screw, M6 x 12 Tightening torque 13 Nm (9.5 ftlb.)    
Vacuum unit to resonance tube Self-tapping screw, internal Torx Tightening torque 5 Nm (3.5 ftlb.)    
Tank vent valve holder to intake-air distributor External Torx screw, M6 x 12 (2x) Tightening torque 13 Nm (9.5 ftlb.)    
Intake manifold pressure sensor to intake-air distributor Oval-head screw, 6.0 x 15 Tightening torque 3 Nm (2 ftlb.)    
Throttle housing to intake-air distributor External Torx screw, M6 x 50 Tightening torque 10 Nm (7.5 ftlb.)    
Cable duct to intake-air distributor External Torx screw, M6 x 16 Tightening torque 13 Nm (9.5 ftlb.)    
Rubber shroud to throttle housing Screw-type clamp Tightening torque 3 Nm (2 ftlb.)    
Air cleaner housing to body Hexagon-head bolt with washer, M6 x 25 Tightening torque 7 Nm (5 ftlb.)    
Air cleaner housing cover Tapping screws Tightening torque 3 Nm (2 ftlb.)    
DME control unit holder to body M6 collar nut Tightening torque 9 Nm (6.5 ftlb.)    
Oxygen sensors for pre-and post-catalytic converters M18 x 1.5 thread - grease with Optimol Paste MF Tightening torque 50 Nm (37 ftlb.) +/-8 Nm (+/-6 ftlb.)  
High-pressure pump to cylinder head External Torx screw, M6 x 25 Initial tightening 7 Nm (5 ftlb.)    
High-pressure pump to cylinder head External Torx screw, M6 x 25 Final tightening torque angle 30° +/-3°  
Union nut for high-pressure line Coat thread with OKS 1710 and leave to dry off Tightening torque 25 Nm (19 ftlb.)    
Fuel line holding clamp to holder External Torx screw, M6 x 12 Tightening torque 10 Nm (7.5 ftlb.)    
High-pressure sensor to fuel collection pipe M10 - grease thread and cone with MicroGleitDF 977 S Tightening torque 22 Nm (16 ftlb.)    
Fuel collection pipe to cylinder head External Torx screw, M6 x 16 Tightening torque 13 Nm (9.5 ftlb.)    
Low-pressure fuel line holder to intake-air distributor External Torx screw, M8 x 12 Tightening torque 12 Nm (9 ftlb.)    
Holder for exhaust flap control valve to intake-air distributor External Torx screw, M6 x 12 Tightening torque 13 Nm (9.5 ftlb.)    
Holder for vacuum reservoir on cylinder bank 4-6 Cheese head bolt, M6 x 12 Tightening torque 10 Nm (7.5 ftlb.)    
Secondary-air pump holder to intake-air distributor for bank 1-3 Screw, M6 x 16 Tightening torque 13 Nm (9.5 ftlb.)    
Rear air guide to body Hexagon nut, M6 Tightening torque 10 Nm (7.5 ftlb.)    
Air guide to air cleaner housing Screw-type clamp Tightening torque 3 Nm (2 ftlb.)    
Air guide in rear wheel housing M6 screw Tightening torque 10 Nm (7.5 ftlb.)    
Connecting piece for air guide in side panel Tapping screw Tightening torque 3 Nm (2 ftlb.)    
Exhaust manifold to cylinder head Hexagon nut, M8 - always replace Tightening torque 30 Nm (22 ftlb.)    
Exhaust manifold to front silencer Screw, M8 x 50 - replace Tightening torque 23 Nm (17 ftlb.)    
Front silencer holder to cylinder head cover External Torx screw, M8 x 20 Tightening torque 23 Nm (17 ftlb.)    
Front silencer to holder Collar nut, M8 - replace Tightening torque 23 Nm (17 ftlb.)    
Front silencer to rear silencer Collar nut, M8 - replace Tightening torque 23 Nm (17 ftlb.)    
Clamp on rear silencer Cheese head bolt, M8 x 50 - replace Tightening torque 23 Nm (17 ftlb.)    
Tailpipe to rear silencer Hexagon nut, M8 Tightening torque 23 Nm (17 ftlb.)    
Heat shield to cylinder head cover External Torx screw, M6 x 12 Tightening torque 13 Nm (9.5 ftlb.)    
Retaining frame with heat protection to body Collar nut, M6 Tightening torque 7 Nm (5 ftlb.)    
Heat protection for retaining frame to heat protection on bumper Tapping screw, 4.8 x 19 Tightening torque 3 Nm (2 ftlb.)    
Tapping screw for retaining frame with heat protection - GT3 RS Tapping screw Tightening torque 3 Nm (2 ftlb.)    
Screw for retaining frame with heat protection - GT3 RS M6 screw Tightening torque 10 Nm (7.5 ftlb.)    
Secondary-air pump to bracket External Torx screw, M6 x 12 Tightening torque 13 Nm (9.5 ftlb.)    
Secondary-air pump holder to crankcase External Torx screw, M6 x 25 Tightening torque 13 Nm (9.5 ftlb.)    
Secondary-air pump bracket to holder External Torx screw, M6 x 16 Tightening torque 13 Nm (9.5 ftlb.)    
Secondary-air pump bracket to intake-air distributor 1-3 External Torx screw, M6 x 16 Tightening torque 13 Nm (9.5 ftlb.)    
Secondary-air lines to cylinder head External Torx screw, M6 x 16 Tightening torque 13 Nm (9.5 ftlb.)    
Secondary air valve to line External Torx screw, M6 x 30 Tightening torque 13 Nm (9.5 ftlb.)    
Secondary-air line to holder External Torx screw, M6 x 12 Tightening torque 13 Nm (9.5 ftlb.)    
Secondary-air line to oil guide External Torx screw, M6 x 12 Tightening torque 13 Nm (9.5 ftlb.)    
Retaining bar on cowl panel frame or battery console Collar nut, M8 Tightening torque 23 Nm (17 ftlb.)    
Terminal clamp to battery terminal M6 nut Tightening torque 6 Nm (4.5 ftlb.)    
Ground lead of battery to cowl panel frame Collar nut, M8 Tightening torque 15 Nm (11 ftlb.)    
Rail on battery console Hexagon-head bolt, M8 Tightening torque 23 Nm (17 ftlb.)    
Battery console to holder Hexagon-head bolt, M8 Tightening torque 23 Nm (17 ftlb.)    
Holder for battery console to body Hexagon-head bolt, M8 Tightening torque 23 Nm (17 ftlb.)    
Generator to bracket External Torx screw, M8 x 90 Tightening torque 15 Nm (11 ftlb.)    
Starter to crankcase External Torx screw, M10 x 35 Tightening torque 45 Nm (33 ftlb.)    
Starter cable to terminal 50 Hexagon nut, M6 or hexagon-head bolt, M6 Tightening torque 7 Nm (5 ftlb.)    
B+ line to starter Collar nut, M8 Tightening torque 18 Nm (13 ftlb.)    
B+ line to generator Collar nut, M8 Tightening torque 18 Nm (13 ftlb.)    
Hall sender to cylinder head Internal Torx screw, M6 x 16 Tightening torque 10 Nm (7.5 ftlb.)    
Knock sensor to crankcase External Torx screw, M8 x 35 Tightening torque 23 Nm (17 ftlb.) +/-2 Nm (+/-1.5 ftlb.)  
Ignition coil to cylinder head cover Internal Torx screw, M6 x 16 Tightening torque 10 Nm (7.5 ftlb.)    
Ground cable for ignition coils to cylinder head cover Cheese head bolt, M6 x 12 Tightening torque 10 Nm (7.5 ftlb.)    
Spark plug Initial tightening Tightening torque 32 Nm (24 ftlb.) +/-2 Nm (+/-1.5 ftlb.)  
Spark plug Second tightening Tightening torque 25 Nm (19 ftlb.) +3 Nm (+2 ftlb.)  
Oil-pressure sender to crankcase Internal Torx screw, M6 x 20 Tightening torque 13 Nm (9.5 ftlb.)    
Oil-level sender to oil tank Hexagon nut, M6 Tightening torque 10 Nm (7.5 ftlb.)    
Control valve to oil guide module External Torx screw, M6 x 16 Tightening torque 13 Nm (9.5 ftlb.)    
Pulse sender to transmission flange Cheese head bolt, M6 x 16 Tightening torque 10 Nm (7.5 ftlb.)    
scientia non olet · About LEMON Manuals