LEMON Manuals: Even more car manuals for everyone
Home >> Porsche >> 2016 >> Cayman GTS, Standard Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 247 (20 - Fuel Supply, Control -- 92A Cayenne) >> WM 208055 Replacing Accelerator Pedal Module (Cayenne Turbo, Cayenne Turbo S, Cayenne S & Cayenne GTS) >> Replacing Accelerator Pedal >> Performing Kickdown Adaptation

Performing Kickdown Adaptation

WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2018 Porsche Cayenne, 2017 Porsche Cayenne, 2016 Porsche Cayenne, 2015 Porsche Cayenne, and 2014 Porsche Cayenne. However, it is still accessible from the selected car via links, so may be relevant.
  1. Connect the Porsche System Tester and switch on the ignition.
  2. Select the relevant vehicle and call up the "Diagnostics" menu.
  3. Control unit overview screen.
    1. 3.1. Control unit search ends and DME control unit is displayed.
    2. 3.2. Read out the fault memory of the DME control unit and correct and erase faults if necessary.
    3. 3.3. Select the "Maintenance/repairs" menu.
  4. Maintenance/repairs screen.
    1. 4.1. Select the Adaptations test.
    2. 4.2. Follow the menu prompting.
  5. Adaptations/preconditions screen.
    1. 5.1. The following preconditions are displayed and must always be observed:
      • No faults stored in the fault memory
      • Engine off
      • Ignition on
      • Accelerator pedal not pressed
      • Parking brake on
      • Engine temperature: 60 °C...90 °C
    2. 5.2. Follow the menu prompts.
  6. Adaptations/overview screen.
    1. 6.1. Select Kickdown threshold adaptation.
    2. 6.2. Follow the menu prompts.
  7. V6 and Hybrid:  Adaptation/Kickdown switch screen.
    1. 7.1. The message "Press accelerator pedal" is displayed.
    2. 7.2. The accelerator pedal must be pressed within 5 seconds. Otherwise, an error message will appear.
    3. 7.3. If the accelerator pedal was pressed within the specified time, the message "System OK" should appear on the Porsche System Tester.
    4. 7.4. If the Porsche System Tester displays an error message, check the preconditions again and repeat the adaptation test again from the start.
    5. 7.5. Press [F8] or STOP on the touchscreen to end the test.
  8. V8 naturally aspirated engine and turbo engine:  Adaptation/Kickdown switch screen:
    1. 8.1. The message "Press the accelerator as far as the mechanical stop and keep it pressed for at least 30 seconds" is displayed.
    2. 8.2. After 30 seconds, the message "System OK" should appear on the Porsche System Tester.
    3. 8.3. If the Porsche System Tester displays an error message, check the preconditions again and repeat the adaptation test again from the start.
    4. 8.4. Press [F8] or STOP on the touchscreen to end the test.
  9. The test is now complete.
  10. Disconnect the Porsche System Tester from the vehicle.
  11. Error messages.
    1. 11.1. Error messages can be displayed if:
      • Not all the preconditions were met.
      • The prompt "Press accelerator pedal" was ignored for more than 8 seconds.
    2. 11.2. If the Porsche System Tester displays an error message, the adaptation test must be repeated from the start.
scientia non olet · About LEMON Manuals