Technical Values: Overview

WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2018 Porsche Cayenne, 2017 Porsche Cayenne, 2016 Porsche Cayenne, 2015 Porsche Cayenne, and 2014 Porsche Cayenne. However, it is still accessible from the selected car via links, so may be relevant.

Location	Description	Type	Basic value	Tolerance 1
Installation dimension for torque converter	Cayenne 3.0 V6 Diesel	Control value	18.9 mm
Installation dimension for torque converter	Cayenne 3.0 V6 (China)	Control value	20.2 mm
Installation dimension for torque converter	Cayenne 3.6 V6	Control value	22.1 mm
Minimum installation dimension for torque converter	Cayenne 4.8 S/GTS/Turbo - check that it is seated correctly and prevent it from tilting	Control value (minimum dimension)	4.5 mm
Installation dimension for torque converter	Cayenne 3.0 S Hybrid	Control value	18.9 mm
Installation dimension for torque converter	Cayenne 4.2 S Diesel	Control value	23.0 mm
Fastening screw on pressure plate	Loosen and tighten screws crosswise and in small steps	Initial tightening	20 Nm (15 ftlb.)
Fastening screw on pressure plate	Loosen and tighten screws crosswise and in small steps	Final tightening	+90°
Fastening screw for actuator		Tightening torque	10 Nm (7.5 ftlb.)
2 fastening screws		Tightening torque	10 Nm (7.5 ftlb.)
Fastening screw		Tightening torque	10 Nm (7.5 ftlb.)
Fastening screw for clamp		Tightening torque	10 Nm (7.5 ftlb.)
Rubber mounting on actuator holder		Tightening torque	10 Nm (7.5 ftlb.)
Rubber mounting on actuator holder		Tightening torque	10 Nm (7.5 ftlb.)
Torque converter to drive plate		Tightening torque	60 Nm (44 ftlb.)
Torque converter to drive plate		Tightening torque	85 Nm (63 ftlb.)
Torque converter to drive plate		Tightening torque	85 Nm (63 ftlb.)
Fastening screw securing ATF line to heat exchanger		Tightening torque	8 Nm (6 ftlb.)
Fastening screw securing ATF line to transmission		Tightening torque	20 Nm (15 ftlb.)
Fastening screw securing ATF line to transmission		Tightening torque	20 Nm (15 ftlb.)
Fastening screw securing ATF line to engine		Tightening torque	8 Nm (6 ftlb.)
Fastening screw securing ATF line to ATF cooler		Tightening torque	20 Nm (15 ftlb.)
Fastening screw securing damper to transfer gear		Tightening torque	32 Nm (24 ftlb.)
Fastening screw securing center bearing to body		Initial tightening	20 Nm (15 ftlb.)
Fastening screw securing center bearing to body		Final tightening	+90°
Fastening screw securing tunnel support to body		Tightening torque	60 Nm (44 ftlb.)
Oil filler screw on transfer gear		Tightening torque	20 Nm (15 ftlb.)
Oil drain plug on transfer gear		Tightening torque	20 Nm (15 ftlb.)
Fastening screw securing transfer gear to transmission	Replace screws	Initial tightening	20 Nm (15 ftlb.)
Fastening screw securing transfer gear to transmission		Final tightening	90°
Transmission support to body	Replace	Initial tightening	50 Nm (37 ftlb.)
Transmission support to body		Final tightening	90°
Transmission bracket to transmission mount	Replace	Initial tightening	50 Nm (37 ftlb.)
Transmission bracket to transmission mount		Final tightening	90°
Transmission bracket to transfer gear	M8 x 35 and M8 x 70	Tightening torque	23 Nm (17 ftlb.)
Oil level	under lower edge of filler screw	Fill quantity	7 mm	+/-2 mm
Oil level	under lower edge of filler screw	Fill quantity	5 mm	+/-2 mm
Oil level	under lower edge of filler screw	Fill quantity	3 mm	+/-2 mm
Oil level	under lower edge of filler screw	Fill quantity	6 mm	+/-2 mm