Technical Values: Overview
WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2018 Porsche Cayenne, 2017 Porsche Cayenne, 2016 Porsche Cayenne, 2015 Porsche Cayenne, and 2014 Porsche Cayenne. However, it is still accessible from the selected car via links, so may be relevant.
| Location | Description | Type | Basic value | Tolerance 1 | Tolerance 2 |
|---|---|---|---|---|---|
| No. 1: Threaded connection securing steering gear to suspension subframe | M12 x 1.5 thread (always replace screws and lock nuts after removal) | Tightening torque | 90 Nm (67 ftlb.) | +90° | |
| No. 2: Threaded connection securing tie rod to pivot bearing | M14 x 1.5 thread (always replace screws and lock nuts after removal) | Tightening torque | 90 Nm (67 ftlb.) | ||
| No. 3: Threaded connection securing tie rod to tie-rod end | M16 x 1.5 thread, lock nut | Tightening torque | 90 Nm (67 ftlb.) | ||
| No. 4: Threaded connection for heat shield | M6 x 16 thread | Tightening torque | 9 Nm (6.5 ftlb.) | ||
| No. 5: Threaded connection securing axial joint to steering rack | M18 x 1.5 thread, axial joint | Tightening torque | 100 Nm (74 ftlb.) | +10° | |
| No. 6: Expansion hose to steering gear | a/f 17 thread (a/f = wrench size 17) | Tightening torque | 32 Nm (24 ftlb.) | +/-4 Nm (+/-3 ftlb.) | |
| No. 7: Return line to steering gear | a/f 17 thread (a/f = wrench size 17) | Tightening torque | 32 Nm (24 ftlb.) | +/-4 Nm (+/-3 ftlb.) | |
| Expansion/return hose to steering gear | M6 x 12 thread | Tightening torque | 9 Nm (6.5 ftlb.) | ||
| No. 8: Heat shield to steering gear | M6 x 16 thread | Tightening torque | 10 Nm (7.5 ftlb.) | ||
| No. 1: Threaded connection securing steering wheel to steering column | M18 x 1.5 x 26 thread (only use screw once) | Tightening torque + torque angle | 30 Nm (22 ftlb.) | +90° | |
| No. 3: Threaded connection securing steering column to assembly bracket | M8 x 32 thread; observe tightening sequence! Tighten anti-clockwise from 1 to 4, starting with the rear right fastening screw. | Tightening torque | 20 Nm (15 ftlb.) | ||
| No. 4: Threaded connection securing steering column to frequency strut | M8 x 115 thread; screw frequency strut to mounting bracket after screwing on steering column! | Tightening torque | 20 Nm (15 ftlb.) | ||
| No. 5: Threaded connection securing mount for sealing ring/seal to firewall | Tightening torque | 4 Nm (3 ftlb.) | |||
| No. 6: Threaded connection securing universal joint to steering gear | M8 x 30 thread (only use screw once) | Tightening torque | 20 Nm (15 ftlb.) | +90° | |
| Contact bridge to steering wheel skeleton | Tightening torque | 6 Nm (4.5 ftlb.) | |||
| Multi-functional switch and front trim to main cover | Tightening torque | 0.45 Nm (0.25 ftlb.) | |||
| Steering wheel skeleton to main cover | Tightening torque | 2 Nm (1.5 ftlb.) | |||
| Paddles to steering wheel skeleton | Tightening torque | 2.5 Nm (2 ftlb.) | |||
| Back cover to steering wheel skeleton | Tightening torque | 2.7 Nm (2 ftlb.) | |||
| No. 1: Hydraulic pump to engine (support) | M8 x 35 thread | Tightening torque | 23 Nm (17 ftlb.) | ||
| No. 2: Pulley to hydraulic pump | M8 x 16 thread | Tightening torque | 23 Nm (17 ftlb.) | ||
| Intake pipe to hydraulic pump | M6 x 12 thread | Tightening torque | 10 Nm (7.5 ftlb.) | ||
| Expansion hose to hydraulic pump | Tightening torque | 32 Nm (24 ftlb.) | +/-4 Nm (+/-3 ftlb.) | ||
| Reservoir | Tightening torque | 10 Nm (7.5 ftlb.) | |||
| No. 2: Hydraulic pump to engine (support) | Tightening torque | 23 Nm (17 ftlb.) | |||
| No. 3: Pulley to hydraulic pump | Tightening torque | 23 Nm (17 ftlb.) | |||
| Suction hose to hydraulic pump | Spring band clamp | Tightening torque | |||
| Expansion hose to hydraulic pump | M6 | Tightening torque | 10 Nm (7.5 ftlb.) | +/-1 Nm (+/-0.5 ftlb.) | |
| Reservoir | Tightening torque | 10 Nm (7.5 ftlb.) | |||
| No. 1: Hydraulic pump to engine (support) | Tightening torque | 23 Nm (17 ftlb.) | |||
| No. 2: Pulley to hydraulic pump | Tightening torque | 23 Nm (17 ftlb.) | |||
| Suction hose to hydraulic pump | Spring band clamp | Tightening torque | |||
| Expansion hose to hydraulic pump | M6 | Tightening torque | 10 Nm (7.5 ftlb.) | +/-1 Nm (+/-0.5 ftlb.) | |
| Reservoir | Tightening torque | 10 Nm (7.5 ftlb.) | |||
| No. 1: Hydraulic pump to engine (support) | Tightening torque | 23 Nm (17 ftlb.) | |||
| No. 2: Pulley to hydraulic pump | Tightening torque | 23 Nm (17 ftlb.) | |||
| Suction hose to hydraulic pump | Spring band clamp | Tightening torque | |||
| Expansion hose to hydraulic pump | M6 | Tightening torque | 10 Nm (7.5 ftlb.) | +/-1 Nm (+/-0.5 ftlb.) | |
| Reservoir | Tightening torque | 10 Nm (7.5 ftlb.) |