Technical Values: Overview
WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2018 Porsche Cayenne, 2017 Porsche Cayenne, 2016 Porsche Cayenne, 2015 Porsche Cayenne, and 2014 Porsche Cayenne. However, it is still accessible from the selected car via links, so may be relevant.
| Location | Description | Type | Basic value | Tolerance 1 | Tolerance 2 |
|---|---|---|---|---|---|
| No. 2: Brake cover plate to front axle | M6 x 12 thread | Tightening torque | 8 Nm (6 ftlb.) | ||
| No. 4: Cable holder to front-axle wheel carrier | M8 x 14 thread | Tightening torque | 20 Nm (15 ftlb.) | ||
| No. 5: Brake hose holder to front-axle wheel carrier | M6 x 12 thread | Tightening torque | 9 Nm (6.5 ftlb.) | ||
| No. 6: Fastening screw securing brake disc to wheel hub | M12 x 1.5 thread (always replace screws and lock nuts after removal) | Tightening torque | 15 Nm (11 ftlb.) | ||
| Mounting for intermediate piece | M6 x 14 thread | Tightening torque | 10 Nm (7.5 ftlb.) | ||
| Deflector to body (tunnel) | M8 x 20 thread | Tightening torque | 23 Nm (17 ftlb.) | ||
| No. 1: Actuator to wheel carrier | Tightening torque | 20 Nm (15 ftlb.) | +60° (+44 ftlb.) | ||
| No. 2: Screw plug for rear brake disc | M12 x 1.5 thread | Tightening torque | 15 Nm (11 ftlb.) | ||
| No. 4: Brake line holder to rear-axle brake calliper | M6 x 12 thread | Tightening torque | 8 Nm (6 ftlb.) | ||
| No. 6: Brake carrier to rear wheel carrier | M6 x 12 thread | Tightening torque | 8 Nm (6 ftlb.) | ||
| No. 7: Fastening screw securing brake disc to wheel hub | M12 x 1.5 thread (always replace screws and lock nuts after removal) | Tightening torque | 15 Nm (11 ftlb.) | ||
| No. 8: Cable holder to control arm | Tightening torque | 8 Nm (6 ftlb.) | |||
| No. 10: ABS cable holder to rear-axle wheel carrier | M6 x 12 thread | Tightening torque | 8 Nm (6 ftlb.) | ||
| No. 1: Pedals (pedal bearing block) to assembly plate | M8 x 20 thread | Tightening torque | 23 Nm (17 ftlb.) | +/-3 Nm (+/- 2 ftlb.) | |
| No. 2: Accelerator pedal to pedal block | Tightening torque | 10 Nm (7.5 ftlb.) | +/-1.5 Nm (+/-1.0 ftlb.) | ||
| No. 3: Clutch master cylinder to pedal block | Thread | Tightening torque | 15 Nm (11 ftlb.) | +/-1 Nm (+/- 0.5 ftlb.) | |
| Cold air bulkhead | Tightening torque | 8 Nm (6 ftlb.) | +/-1.5 Nm (+/-1 ftlb.) | ||
| No. 1: Clutch slave cylinder to transmission | M8 x 25 thread | Tightening torque | 23 Nm (17 ftlb.) | +/-2 Nm (+/- 1.5 ftlb.) | |
| No. 2: Ventilation valve to clutch slave cylinder | Thread | Tightening torque | 6 Nm (4.5 ftlb.) | +/-1 Nm (+/- 0.5 ftlb.) |