LEMON Manuals: Even more car manuals for everyone
Home >> Porsche >> 2016 >> Cayman Base, Automatic DCT Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 163 (42 - Rear Wheel Suspension, Drive Shafts -- CARRERA (997)) >> WM 423819 Removing And Installing Rear-Axle Carrier Side Section (Except 911 Turbo S Coupe "Ed. 918 SPYDER", 911 CARRERA 4 GTS, 911 CARRERA 4 GTS CABRIO, 911 Gt3 RS 4.0) >> Removing And Installing Rear-Axle Carrier Side Section >> Installing Rear-Axle Carrier Side Section

Installing Rear-Axle Carrier Side Section

WARNING: This page does not describe the selected car, but rather 9 other vehicles, including the 2013 Porsche 911, 2012 Porsche 911, 2011 Porsche 911, 2010 Porsche 911, and 2009 Porsche 911. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: Overview Of Rear-Axle Carrier Side Section
G09825697Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  1. Rear-axle carrier side section
  2. Lock nut (replace)
  3. Washer
  4. Stud, M12
  5. Elastic bolt, M12 (replace)
  6. Screw, M12
  7. Lock nut, M12 (replace)
  8. Transverse strut
  9. Screw, M10
  10. Diagonal brace
  11. Rubber mount
  12. Screw, M10 or M12
  13. Screw, M12
  14. Cross member
  15. Screw, M12
  16. Lock nut, M12 (replace)
  17. Sensor
  18. Brake hose bracket
  19. M6 screw

Replace all lock nuts and screws -5-. 

  1. Install rear-axle carrier side section -1-  .

    Fit rear-axle carrier side section -1-  . Loosely fit lock nut -7-  and screws -5, 6-  .

    Fig 2: Identifying Rear-Axle Carrier Side Section
    G09825698Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  2. Fit upper control arm -8-  .

    Fit both control arms -8-  at the rear-axle carrier side section. To do this, screw in (fit) bolts -11, 12-  .

    Fig 3: Identifying Upper Control Arms Components
    G09825699Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  3. Fit lower control arms -13, 21-  .

    Insert both control arms -13, 21-  on the rear-axle carrier side section and screw in (fit) bolts -12, 15, 22-  .

    Fig 4: Identifying Lower Control Arms Components
    G09825700Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  4. Install cross member -14-  .

    Insert cross member -14-  and fit M12 x 80 bolts -15, 16-  .

    Fig 5: Identifying Cross Member
    G09825701Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  5. Install diagonal braces -10-  .

    Fit diagonal braces -10-  and screw in (fit) screws -12, 13-  .

    Fig 6: Identifying Diagonal Brace
    G09825702Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  6. Install the transverse strut.

    Fit transverse strut and screw in (fit) screws.

  7. Fit brake hose bracket on the rear-axle carrier side section.
  8. Install diagonal arm -17-  .
    1. 8.1. Insert diagonal arm -17-  and fit it on the wishbone -21-  . To do this, screw in (fit) bolts -19, 20-  .
    2. 8.2. Fit diagonal arm -17-  on the rear-axle carrier side section -1-  . To do this, screw in (fit) bolts -18, 19-  .
    Fig 7: Identifying Removing/Installing Components Of Diagonal Arm
    G09825703Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  9. Tighten the rear axle.

    Observe prescribed tightening sequence so as not to twist the rear axle. 

    1. 9.1. Tighten front rear-axle carrier side section -7-  at the left and right.

      Stud -4-  securing rear-axle carrier side section to body (front)

      → Tightening torque: 46 Nm (34 ftlb.) 

      Lock nut -7-  securing rear-axle carrier side section to body (front)

      → Tightening torque: 110 Nm (81.5 ftlb.) 

    2. 9.2. Tighten rear rear-axle carrier side section -6-  at the left and right.
    3. 9.3. Tighten center rear-axle carrier side section -5-  at the left and right.

      Rear-axle carrier side section to body (center and rear) -5 and 6-

      → Tightening torque: 110 Nm (81.5 ftlb.) 

      Fig 8: Identifying Rear-Axle Carrier Side Section
      G09825704Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    4. 9.4. Tighten cross member -14-  to carrier side section at the bottom left/right first, then at the top left/right.

      → Tightening torque: 110 Nm (81.5 ftlb.) 

      Fig 9: Identifying Cross Member
      G09825705Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    5. 9.5. Tighten diagonal brace to the body -12-  at the left and right.

      → Tightening torque: M10=65 Nm (48 ftlb.) 

      → Tightening torque: M12=110 Nm (81.5 ftlb.) 

    6. 9.6. Tighten diagonal brace to the cross member -13-  at the left and right.

      → Tightening torque: 110 Nm (81.5 ftlb.) 

    7. 9.7. Tighten diagonal brace to rear-axle carrier side section (M10 collar nut).

      → Tightening torque: 23 Nm (17 ftlb.) 

    8. 9.8. Tighten transverse strut to (front) rear-axle carrier side section at the left and right.

      → Tightening torque: 65 Nm (48 ftlb.) 

      9. Fig 10: Identifying Diagonal Brace
      G09825706Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  10. Tighten all trailing arms.
    1. 10.1. Tighten diagonal arm.

      Diagonal arm to rear-axle carrier side section

      → Tightening torque: 180 Nm (133 ftlb.) 

      Diagonal arm to wishbone

      → Tightening torque: 160 Nm (118 ftlb.) 

    2. 10.2. Tighten upper control arms.

      → Tightening torque: 110 Nm (81.5 ftlb.) 

    3. 10.3. Tighten lower control arms (toe and transverse control arms) (toe and camber eccentrics).

      Set the toe and camber eccentrics to the original position (previously marked position) -arrows-  of the rear-axle carrier side section. Copy the previously marked position from the old rear-axle carrier side section to the new part if necessary. Tighten the lock nuts.

      → Tightening torque: 100 Nm (74 ftlb.) 

      Fig 11: Locating Eccentric Threaded Joint
      G09825707Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  11. Fit anti-roll bar on rear-axle carrier side section.

    Screw in and tighten screws -1-  .

    → Tightening torque: 23 Nm (17 ftlb.) 

    Fig 12: Fitting Anti-Roll Bar
    G09825708Courtesy of PORSCHE CARS NORTH AMERICA, INC.
scientia non olet · About LEMON Manuals