Technical Values

WARNING: This page is about a different car, the 2014 Porsche Cayenne, 2013 Porsche Cayenne, 2012 Porsche Cayenne, and 2011 Porsche Cayenne. However, it is still accessible from the selected car via links, so may be relevant.

Location	Basic val...	Toleranc...
Press-in depth to fitting bore	19 mm
Press-in depth to fitting bore	17 mm
Press-in depth	2.5 mm	+/- 0.2 mm
Press-in depth	7.5 mm	+/- 0.2 mm

Model year

From 2014

Vehicle Type:

Panamera/Panamera S/Panamera GTS/Panamera Turbo/Panamera Turbo S

Cayenne S (92A)/Cayenne GTS (92A)/Cayenne Turbo (92A)/Cayenne Turbo S (92A)

Concerns:

Radial shaft seal for crankshaft (sealing ring, transmission side)

Information:

A different special tool is required because of the different press-in depth.

The crankcase has been modified and for this reason, the press-in depth of the sealing ring has also changed with the changeover from MY D (2013) to MY E (2014).

Information

If the sealing ring needs to be replaced , the existing press-in depth must always be measured before removing the sealing ring:

The depth is measured from the outer edge of the crankcase (-item 2- ) to the surface of the sealing ring (-item 4- ).

Courtesy of PORSCHE CARS NORTH AMERICA, INC.

As a result, the sealing ring MUST be installed using the relevant special tool , depending on the crankcase used:

Measured depth "-a- " (between sealing ring and crankcase - -items 1 and 2- ):

Press-in depth: > 2.5 mm +/- 0.2 mm

=> corresponds to crankcase used up to MY D (2013).

Courtesy of PORSCHE CARS NORTH AMERICA, INC.

=> Install sealing ring (Part No. 997.101.212.01) only using special tool:

> 9609 - Insertion tool,
crankcase > 9609/1 - pressure piece and
> 9609/2 - spacer.

Measured depth "-a- " (between sealing ring and crankcase - -items 1 and 2- ):

Press-in depth: > 7.5 mm +/- 0.2 mm

=> corresponds to crankcase used as of MY E (2014).

Courtesy of PORSCHE CARS NORTH AMERICA, INC.

=> Install sealing ring (Part No. 997.101.212.01) only using special tool:

> 9837 - Insertion tool.

Information

If the sealing ring (-item 1- ) is unintentionally removed without first measuring the existing press-in depth, the depth is measured from the outer edge of the crankcase (-item 2- ) to the end of the fitting bore:

For crankcase as of MY E: Press-in depth to fitting bore > 19mm
For crankcase up to MY D: Press-in depth to fitting bore > 17mm

Courtesy of PORSCHE CARS NORTH AMERICA, INC.

Date of Introduction:

With changeover from MY D (2013) to MY E (2014).

Affected engine types:

M48.02/M48.52

MCWAA/MCXNA/MCWDA/MCWFA/MCXPA/MCXRA/MCWBA

Parts Info:

997.101.212.01 > Sealing ring (crankshaft, transmission side => valid for both crankcase variants)

Tools:

> 9609 - Insertion tool,

> 9609/1 - pressure piece and

> 9609/2 - spacer or

> 9837 - Insertion tool

References:

>WM, 135919 REMOVING AND INSTALLING SEALING RING FOR CRANKSHAFT - FLYWHEEL SIDE