| Rear-axle valve block to body |
Screw, M6 x 30 |
Tightening torque |
10 Nm (7.5 ftlb.) |
|
|
| T-piece to holder |
Screw, M6 x 30 |
Tightening torque |
10 Nm (7.5 ftlb.) |
|
|
| T-piece with holder to mounting for diagonal arm |
Screw, M6 x 16 |
Tightening torque |
10 Nm (7.5 ftlb.) |
|
|
| Pressure line, top and bottom in T-piece |
Cap screw, M14 x 1.5 |
Tightening torque |
28 Nm (21 ftlb.) |
|
|
| Combination holder (pressure and return lines) to crankcase |
Screw, M6 x 35 |
Tightening torque |
13 Nm (9.5 ftlb.) |
|
|
| Pressure line to combination holder |
Screw, M6 x 30 |
Tightening torque |
10 Nm (7.5 ftlb.) |
|
|
| Combination holder (pressure line connection point) with collection pipe to cylinder head |
Screw, M6 x 25 |
Tightening torque |
13 Nm (9.5 ftlb.) |
|
|
| Front-axle valve block to body |
Screw, M8 x 20 |
Tightening torque |
23 Nm (17 ftlb.) |
|
|
| Front-axle valve block to holder |
Screw, M6 x 30 |
Tightening torque |
10 Nm (7.5 ftlb.) |
|
|
| Holder for fixing device for front-axle lines to body |
Screw, M6 x 40 |
Tightening torque |
10 Nm (7.5 ftlb.) |
|
|
| Connecting link (PDCC actuator) to anti-roll bar |
M12 x 1.5 thread |
Initial tightening |
50 Nm (37 ftlb.) |
|
|
| Connecting link (PDCC actuator) to anti-roll bar |
M12 x 1.5 thread |
Final tightening |
+50° |
|
|
| Connecting link (PDCC actuator) to spring strut (actuator holder) |
Collar nut, M12 x 1.5 |
Initial tightening |
50 Nm (37 ftlb.) |
|
|
| Connecting link (PDCC actuator) to spring strut (actuator holder) |
Collar nut, M12 x 1.5 |
Final tightening |
+50° |
|
|
| Actuator holder (PDCC) to spring strut (shock absorber pipe) |
Hexagon-head bolt, M10 x 55 |
Tightening torque |
46 Nm (34 ftlb.) |
|
|
| Hydraulic lines to connecting link (PDCC actuator) |
Banjo bolt, M12 x 1.5 |
Tightening torque |
26 Nm (19 ftlb.) |
|
|
| Holder for fixing device for pressure lines to connecting link (PDCC actuator) |
Countersunk screw, M6 x 12 |
Tightening torque |
10 Nm (7.5 ftlb.) |
|
|
| Connecting link (PDCC actuator) to anti-roll bar |
Collar nut, M12/always use new collar nut following removal |
Initial tightening |
50 Nm (37 ftlb.) |
|
|
| Connecting link (PDCC actuator) to anti-roll bar |
Collar nut, M12/always use new collar nut following removal |
Final tightening |
+50° |
|
|
| Connecting link (PDCC actuator) to wheel carrier |
Cheese head bolt with hexagon nut, M12 |
Initial tightening |
50 Nm (37 ftlb.) |
|
|
| Connecting link (PDCC actuator) to wheel carrier |
Cheese head bolt with hexagon nut, M12 |
Final tightening |
+50° |
|
|
| Hydraulic lines to connecting link (PDCC actuator) |
Banjo bolt, M12 x 1.5 |
Tightening torque |
26 Nm (19 ftlb.) |
|
|
| Mounting for hydraulic pump |
M8 x 60 |
Tightening torque |
23 Nm (17 ftlb.) |
|
|
| Pump support from hydraulic pump to crankcase |
M6 x 60 |
Tightening torque |
13 Nm (9.5 ftlb.) |
|
|
| Pulley to hydraulic pump |
M8 x 12 |
Tightening torque |
23 Nm (17 ftlb.) |
|
|
| Pressure line to hydraulic pump |
Banjo bolt, M14 x 1.5 |
Tightening torque |
35 Nm (26 ftlb.) |
|
|
| Reservoir to hydraulic pump, top |
M6 x 60 |
Tightening torque |
10 Nm (7.5 ftlb.) |
|
|
| Reservoir to hydraulic pump, bottom |
M6 x 35 |
Tightening torque |
10 Nm (7.5 ftlb.) |
|
|
| PDCC control unit to body |
Plastic nut |
Tightening torque |
2 Nm (1.5 ftlb.) |
|
|