WM 131020 Removing And Installing Pistons And Handling Tools (Except Turbo Coupe, Turbo S Coupe, Turbo S Coupe "Ed. 918 SPYDER", CARRERA 4 GTS, Turbo S CABRIO, Turbo S CABRIO "Ed. 918 SPYDER", CARRERA 4 GTS CABRIO, Gt3, Gt2, Gt3 RS, Gt2 RS, Gt3 RS 4.0): Tools
WARNING: This page does not describe the selected car, but rather 9 other vehicles, including the 2013 Porsche 911, 2012 Porsche 911, 2011 Porsche 911, 2010 Porsche 911, and 2009 Porsche 911. However, it is still accessible from the selected car via links, so may be relevant.
| Designation | Type | Number | Description | |
|---|---|---|---|---|
| locating pin | Special tool | 9595/1 | ||
| assembly aid | Special tool | 9598 | ||
| Disassembly tool | Special tool | 9764 | ||
| turning device | Special tool | 9773 | ||
| Assembly tool | Special tool | 9776 | ||
| Disassembly tool | Special tool | 9777 | ||
| Retaining device | Special tool | 9778 | ||
| Piston receiving element | Special tool | 9778/1 | ||
| holding bridge | Special tool | 9779 | ||
| Centering mandrel | Special tool | 9782 | ||
| Assembly aid | Special tool | 9783 | ||
| Funnel | Special tool | 9784 | ||
| funnel | Special tool | 9784/2 | ||
| Piston assembly aid | Special tool | 9787 | ||
| piston assembly aid | Special tool | 9787/1 | ||
| assembly aid | Special tool | 9795 |
Tool overview
- Retaining device 9778 with piston receiving element with a diameter of 97 mm.
- Piston receiving element 9778/1 , diameter: 102 mm.
- Funnel 9784 or funnel 9784/2 for piston assembly, diameter: 97 mm or 102 mm.
- Piston assembly aid 9787 , diameter: 97 mm or piston assembly aid 9787/1 , diameter: 102 mm.
- Handle for assembly aid 9598 .
- Disassembly tool 9764 for piston-pin circlips.
- Disassembly tool 9777 and assembly tool for piston pins.
- Assembly tool 9776 for piston-pin circlips.
- Centering mandrel 9782 for connecting rods and pistons.
- Assembly aid 9783 for pressing out pistons (cylinders 1-3) and connecting rods with pistons (cylinders 4-6).
Not shown - Rubber sleeves, assembly aid 9795 for protecting cylinder linings (fitted on connecting rods for cylinders 1-3).
| Designation | Type | Number | Description | |
|---|---|---|---|---|
| locating pin | Special tool | 9595/1 | ||
| assembly aid | Special tool | 9598 | ||
| Disassembly tool | Special tool | 9764 | ||
| turning device | Special tool | 9773 | ||
| Assembly tool | Special tool | 9776 | ||
| Disassembly tool | Special tool | 9777 | ||
| Retaining device | Special tool | 9778 | ||
| Piston receiving element | Special tool | 9778/1 | ||
| holding bridge | Special tool | 9779 | ||
| Centering mandrel | Special tool | 9782 | ||
| Assembly aid | Special tool | 9783 | ||
| Funnel | Special tool | 9784 | ||
| funnel | Special tool | 9784/2 | ||
| Piston assembly aid | Special tool | 9787 | ||
| piston assembly aid | Special tool | 9787/1 | ||
| assembly aid | Special tool | 9795 |
Tool overview
- Retaining device 9778 with piston receiving element with a diameter of 97 mm.
- Piston receiving element 9778/1 , diameter: 102 mm.
- Funnel 9784 or funnel 9784/2 for piston assembly, diameter: 97 mm or 102 mm.
- Piston assembly aid 9787 , diameter: 97 mm or piston assembly aid 9787/1 , diameter: 102 mm.
- Handle for assembly aid 9598 .
- Disassembly tool 9764 for piston-pin circlips.
- Disassembly tool 9777 and assembly tool for piston pins.
- Assembly tool 9776 for piston-pin circlips.
- Centering mandrel 9782 for connecting rods and pistons.
- Assembly aid 9783 for pressing out pistons (cylinders 1-3) and connecting rods with pistons (cylinders 4-6).
Not shown - Rubber sleeves, assembly aid 9795 for protecting cylinder linings (fitted on connecting rods for cylinders 1-3).