LEMON Manuals: Even more car manuals for everyone
Home >> Porsche >> 2016 >> 911 Turbo, 2D Convertible >> Repair and Diagnosis >> External Pages >> Different car >> Section 104 (61 - Convertible Top, Hardtop -- CARRERA (997)) >> WM 610919 Removing And Installing Hood Inner Lining (CABRIO Models) >> Installing Hood Inner Lining >> Installing Hood Inner Lining At Front

Installing Hood Inner Lining At Front

WARNING: This page does not describe the selected car, but rather 9 other vehicles, including the 2013 Porsche 911, 2012 Porsche 911, 2011 Porsche 911, 2010 Porsche 911, and 2009 Porsche 911. However, it is still accessible from the selected car via links, so may be relevant.
  1. Pull hood inner-lining joint -1-  into the front groove on the corner bow -arrow A-  and Centre it.
    Fig 1: Installing Corner Bow Joint
    G09831835Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  2. Fit joint strip -2-  into the rear groove -arrows B-  .
  3. Position the bracing strap -2-  at the left and right under the hood inner lining -3-  and secure to the main folding top bow with the fastening screw -1-  (-arrow-  ).
    Fig 2: Installing Brace
    G09831836Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  4. Pull bracing strap -1-  at the left and right into the plastic joint on the hood inner lining -2-  .
    Fig 3: Identifying Bracing Strap
    G09831837Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  5. Press Velcro fastener at the left and right of the hood inner lining onto the corner bow -arrow-  .
    Fig 4: Closing Velcro Fastener
    G09831838Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  6. Position hood inner lining bracing strap on the side -2-  at the left and right above the tension strap bracing strap -1-  . Follow the sequence shown.
    Fig 5: Installing Bracing Straps
    G09831839Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  7. Screw fastening screw -3-  and bracing straps to the main folding top bow -arrow-  .

    The wire harness for the hood -4-  is also secured on the left side.

  8. Close the zip -2-  between the hood inner lining at the front -1-  and the joint in the hood covering -3-  in -direction of arrow-  .

    Lock the zip using a paper clip -4-  .

    Fig 6: Closing Zip
    G09831840Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  9. Secure hood inner-lining joint -2-  at the left and right with fastening screws -1-  (-arrow-  ).
    Fig 7: Securing Hood Inner-Lining Joint
    G09831841Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  10. Close the Velcro fastener -1-  at the left and right between the hood inner lining at the side -2-  and the corner bow -3-  (-arrow-  ).
    Fig 8: Closing Velcro Fastener
    G09831842Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  11. Position covering strip -2-  on the roof frame (2) and press in expanding clip -1-  (-arrow-  ).
    Fig 9: Fitting Roof Frame Hood Inner-Lining Joint
    G09831843Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  12. Fit rear sewn-on clamping rail on the roof frame (1) at the left and right -arrows-  .
    Fig 10: Fitting Rear Clamping Rail
    G09831844Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  13. Fit front sewn-on clamping rail on the roof frame (1) at the left and right -arrows-  .
    Fig 11: Fitting Front Clamping Rail
    G09831845Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  14. Secure hood inner-lining joint with the fastening screws at the left and right -arrow-  .
    Fig 12: Tightening Front Clamping Rail
    G09831846Courtesy of PORSCHE CARS NORTH AMERICA, INC.
scientia non olet · About LEMON Manuals