Technical Values

WARNING: This page does not describe the selected car, but rather 9 other vehicles, including the 2013 Porsche 911, 2012 Porsche 911, 2011 Porsche 911, 2010 Porsche 911, and 2009 Porsche 911. However, it is still accessible from the selected car via links, so may be relevant.

Location	Description	Type	Basic value
Bearing pin securing tensioning rail for oil-pump drive chain	M6, replace O-ring	Tightening torque	10 Nm (7.5 ft. lb.)
Bearing pins securing guide and tensioning rails	M6, replace O-rings	Tightening torque	10 Nm (7.5 ft. lb.)
Through-bolt screws, Step 1	Replace sealing washers	Initial tightening	5 Nm (3.5 ft. lb.)
Through-bolt screws, Step 2		Initial tightening	12 Nm (9 ft. lb.)
Through-bolt screws, Step 3		Tightening torque	15 Nm (11 ft. lb.)
Through-bolt screws, Step 4		Torque angle	75°
Through-bolt screws, Step 5		Final tightening - torque angle	75°
Supporting mount screws	External Torx screw, M8 x 35	Initial tightening	5 Nm (3.5 ft. lb.)
Supporting mount screws		Torque angle	70°
Cross bolt connection	External Torx screw, M8 x 120	Tightening torque	33 Nm (24 ft. lb.)
Cross bolt connection	External Torx screw, M6	Tightening torque	13 Nm (9.5 ft. lb.)
Oil guide to crankcase	M6 x 20	Tightening torque	13 Nm (9.5 ft. lb.)
Coolant pipe mounting	External Torx screw, M6 x 12	Tightening torque	13 Nm (9.5 ft. lb.)
Solenoid hydraulic valve	M5 x 12	Tightening torque	8 Nm (6 ft. lb.)
Coolant pipe to cylinder head (intake side)	External Torx screw, M6 x 12	Tightening torque	13 Nm (9.5 ft. lb.)
Threaded bolt for engine carrier	Bond with Loctite 243	Tightening torque	5 Nm (3.5 ft. lb.)
Connecting tube on coolant regulator housing	External Torx screw, M6 x 25, tighten first	Tightening torque	13 Nm (9.5 ft. lb.)
Coolant regulator housing to cylinder head	External Torx screw, M6 x 50	Tightening torque	13 Nm (9.5 ft. lb.)
Coolant pump bracket and unit carrier	External Torx screw, M8 x 35, M8 x 50, M8 x 70	Tightening torque	33 Nm (24 ft. lb.)
Coolant pump bracket	M8 x 25	Tightening torque	23 Nm (17 ft. lb.)
Coolant pump bracket	M6 x 20	Tightening torque	13 Nm (9.5 ft. lb.)
Vibration damper to crankshaft flange	External Torx screw, M8 x 1 x 25	Tightening torque	60 Nm (44 ft. lb.)
Coolant pipe to coolant regulator housing	External Torx screw, M6 x 12	Tightening torque	13 Nm (9.5 ft. lb.)
Vacuum line holder to oil pan	External Torx screw, M6 x 12	Tightening torque	10 Nm (7.5 ft. lb.)
Union nut on fuel lines	OKS 1700 lubricant	Tightening torque	20 Nm (15 ft. lb.)
Holder for fuel lines	External Torx screw, M6	Tightening torque	13 Nm (9.5 ft. lb.)
Heat shield for high-pressure pump to cylinder head	External Torx screw, M6	Tightening torque	13 Nm (9.5 ft. lb.)
Heat shield for high-pressure pump	External Torx screw, M6 x 12	Tightening torque	13 Nm (9.5 ft. lb.)
Coolant regulator housing cover and intake tube	External Torx screw, M6	Tightening torque	13 Nm (9.5 ft. lb.)
Exhaust manifold to cylinder head	External Torx screw, M8 x 27	Initial tightening	12 Nm (9 ft. lb.)
Exhaust manifold to cylinder head	External Torx screw, M8 x 27	Final tightening	30 Nm (22 ft. lb.)
Turbocharger holder to cylinder head	External Torx screw, M8 x 35	Tightening torque	23 Nm (17 ft. lb.)
Coolant distributor to crankcase	External Torx screw, M6 x 25	Tightening torque	13 Nm (9.5 ft. lb.)
Transport eyebolt to crankcase	External Torx screw, M6 x 25	Tightening torque	13 Nm (9.5 ft. lb.)
Knock sensor to cylinder head	External Torx screw, M8 x 35	Tightening torque	23 Nm (17 ft. lb.)
Fuel collection pipe	External Torx screw, M6 x 30	Tightening torque	13 Nm (9.5 ft. lb.)
Bracket for oil/water heat exchanger	External Torx screw, M6 x 45 and M6 x 60	Tightening torque	13 Nm (9.5 ft. lb.)
Oil/water heat exchanger	Internal Torx screw, M6 x 20	Contact force	13 Nm (9.5 ft. lb.)
Oil separator to bracket	External Torx screw, M6 x 25	Tightening torque	13 Nm (9.5 ft. lb.)
Secondary-air lines and holder	External Torx screws, M6 - replace seals	Tightening torque	13 Nm (9.5 ft. lb.)
Cable duct to cylinder head	External Torx screw, M8 x 16	Tightening torque	23 Nm (17 ft. lb.)
Union nut on fuel connection line	OKS 1700 lubricant	Tightening torque	20 Nm (15 ft. lb.)
Holder for fuel connection line	External Torx screw, M6	Tightening torque	13 Nm (9.5 ft. lb.)
Oil filler neck in crankcase	External Torx screw, M6 x 20	Tightening torque	13 Nm (9.5 ft. lb.)
Heat shield to cylinder head	External Torx screw, M6 x 12	Tightening torque	10 Nm (7.5 ft. lb.)
Oil and coolant lines on turbocharger	External Torx screws, M6	Tightening torque	10 Nm (7.5 ft. lb.)
Intake-air distributor to cylinder head	External Torx screw, M6 x 35	Tightening torque	13 Nm (9.5 ft. lb.)
Intake air line to turbocharger	External Torx screw, M6	Tightening torque	10 Nm (7.5 ft. lb.)
Secondary-air pump to holder	External Torx screw, M6 x 50	Tightening torque	13 Nm (9.5 ft. lb.)
Cable duct to intake-air distributor	External Torx screw, M6 x 12	Tightening torque	13 Nm (9.5 ft. lb.)
Oil filler neck to holder	External Torx screw, M6 x 12	Tightening torque	13 Nm (9.5 ft. lb.)
Hydraulic pump pulley	External Torx screw, M8 x 12	Tightening torque	23 Nm (17 ft. lb.)