LEMON Manuals: Even more car manuals for everyone
Home >> Porsche >> 2015 >> Macan S >> Repair and Diagnosis >> External Pages >> Different car >> Section 620 (37 Automatic Transmission - Actuator, Housing -- (95B) MACAN) >> WM 375519 Removing And Installing ATF Pan (Except MACAN Sport Edition) >> Technical Values >> Front-axle carrier

Front-axle carrier

WARNING: This page is about a different car, the 2018 Porsche Macan and 2017 Porsche Macan. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: Exploded View Of Front-Axle Carrier Components With Torque Specification
G11983527Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  1. Front-axle carrier
  2. Fastening screws → Tightening torque: 9 Nm (6.5 ftlb.) 
  3. Fastening screw → Tightening torque: 20 Nm (15 ftlb.) 
  4. Right heat shield on front-axle carrier
  5. Fastening screws → Tightening torque: 20 Nm (15 ftlb.) 
  6. Right heat shield over engine mount
  7. Left heat shield on front-axle carrier
  8. Fastening screws → Tightening torque: 9 Nm (6.5 ftlb.) 
  9. Fastening screw → Tightening torque: 20 Nm (15 ftlb.) 
  10. Fastening screws → Tightening torque: 20 Nm (15 ftlb.) 
  11. Left heat shield on engine mount
  12. Fastening screws/replace → Tightening torque: 30 Nm (22 ftlb.) 
  13. Retainer plate for engine mount
  14. Engine mount
  15. Fastening screw/replace → Initial tightening: 90 Nm (67 ftlb.) → Final tightening: +90° 
  16. Square nut/replace 
  17. Fastening screws/replace → Initial tightening: 115 Nm (85 ftlb.) → Final tightening: +90° 
  18. Stud/replace if damaged 
  19. Fastening screw/replace → Initial tightening: 115 Nm (85 ftlb.) → Final tightening: +90° 
  20. Fastening screws → Tightening torque: 55 Nm (41 ftlb.) 
  21. Rear fastening screws to cross-strut/replace → Initial tightening: 90 Nm (67 ftlb.) → Final tightening: +135° 
  22. Front fastening screw to cross-strut/replace → Initial tightening: 90 Nm (67 ftlb.) → Final tightening: +90° 
  23. Cross-strut for front-axle carrier
  24. Shock absorber fork
  25. Fastening screw/replace → Initial tightening: 40 Nm (30 ftlb.) → Final tightening: +90° 
    • Must be tightened at empty weight position
  26. Connecting link
  27. Fastening screw/replace → Initial tightening: 40 Nm (30 ftlb.) → Final tightening: +90° 
    • Must be tightened at empty weight position
  28. Fastening nut/replace → Tightening torque: 25 Nm (19 ftlb.) 
  29. Clip
  30. Rubber mounting
    • Opening in the rubber mounting must be facing the front-axle carrier during installation.
    • The anti-roll bar and rubber mounting be free of grease during assembly.
  31. Anti-roll bar
  32. Fastening nut
  33. Fastening screw for protective plate → Tightening torque: 20 Nm (15 ftlb.) 
  34. Protective plate
scientia non olet · About LEMON Manuals