| Brake calliper to front and rear axle (PCCB and grey cast-iron brakes) |
M12 x 1.5/always use new screws on front and rear axle following removal. Different screw length on front and rear axle |
Tightening torque |
85 Nm (63 ftlb.) |
|
|
| Brake hose bracket to wheel bearing housing |
M6 |
Tightening torque |
10 Nm |
|
|
| Brake hose bracket/combined holder to rear wheel bearing housing (wheel carrier) |
M6 |
Tightening torque |
10 Nm |
|
|
| Brake line to brake calliper |
M10 x 1 |
Tightening torque |
16 Nm (12 ftlb.) |
|
|
| Brake cover plate to front and rear axle |
M6 |
Tightening torque |
10 Nm (7.5 ftlb.) |
|
|
| Spreader device (actuator) to wheel carrier |
Hexagon-head bolts, always use new bolts following removal |
Initial tightening |
10 Nm (7.5 ftlb.) |
|
|
| Spreader device (actuator) to wheel carrier |
Hexagon-head bolts, always use new bolts following removal |
Final tightening |
+60° |
|
|
| Brake cover plate to rear axle |
M6 |
Tightening torque |
10 Nm (7.5 ftlb.) |
|
|
| Brake disc to wheel hub (front and rear axle) |
M6 |
Tightening torque |
10 Nm (7.5 ftlb.) |
|
|
| Brake cover plate to front and rear axle |
M6 |
Tightening torque |
10 Nm (7.5 ftlb.) |
|
|
| Speed sensor to front and rear axle |
M6 |
Tightening torque |
10 Nm (7.5 ftlb.) |
|
|
| Pedal module to body |
Hexagon-head bolt, M8 x 25 |
Tightening torque |
23 Nm (17 ftlb.) |
|
|
| Pedal module to body |
Hexagon nut, M8 |
Tightening torque |
23 Nm (17 ftlb.) |
|
|
| Accelerator pedal box to body |
Screw, M6 x 20 |
Tightening torque |
10 Nm (7.5 ftlb.) |
|
|
| Brake line to brake master cylinder |
Cap screw, M12 x 1 |
Tightening torque |
16 Nm (12 ftlb.) |
|
|
| Brake pressure line to hydraulic unit |
Cap screw, M14 x 1 and M12 x 1 |
Tightening torque |
16 Nm (12 ftlb.) |
|
|
| Brake lines to brake hose (front and rear axle) |
M10 x 1 |
Tightening torque |
16 Nm (12 ftlb.) |
|
|
| Transfer points - brake line to brake line |
Cap screw, M10 x 1 |
Tightening torque |
14 Nm (10.5 ftlb.) |
|
|
| Brake lines to brake calliper (front and rear axle) |
M10 x 1 |
Tightening torque |
16 Nm (12 ftlb.) |
|
|
| Brake lines to brake calliper (front and rear axle) |
M10 x 1 |
Tightening torque |
16 Nm (12 ftlb.) |
|
|
| Ventilation valve to brake calliper |
M10 x 1 |
Tightening torque |
14 Nm (10.5 ftlb.) |
|
|
| Connecting line to brake calliper |
M10 x 1 |
Tightening torque |
16 Nm (12 ftlb.) |
|
|
| Brake calliper to wheel carrier, front and rear axle (PCCB and grey cast-iron brakes) |
M12 x 1.5/always use new screws on front and rear axle following removal. Different screw length on front and rear axle
. |
Tightening torque |
85 Nm (63 ftlb.) |
|
|
| Brake booster to pedal module |
Torx screw, M8 x 165 x 77 |
Tightening torque |
23 Nm (17 ftlb.) |
|
|
| Brake master cylinder to brake booster |
Hexagon nut, M14 |
Tightening torque |
49 Nm (36 ftlb.) |
+/-4 Nm (+/-3 ftlb.) |
|
| Brake fluid reservoir to brake master cylinder |
Torx screw, E7 |
Tightening torque |
8 Nm (6 ftlb.) |
|
|
| Brake line to brake master cylinder |
Cap screw, M12 x 1 |
Tightening torque |
16 Nm (12 ftlb.) |
|
|
| Vacuum pump to engine |
Torx screw, M6 |
Tightening torque |
10 Nm (7.5 ftlb.) |
|
|
| Hydraulic unit to holder, upper part |
Screw, M10 x 16 |
Tightening torque |
27 Nm (20 ftlb.) |
|
|
| Lower part of holder for hydraulic unit to body |
Screw, M8 x 20 |
Tightening torque |
23 Nm (17 ftlb.) |
|
|
| Lower part of holder for hydraulic unit to body |
Screw, M6 x 25 |
Tightening torque |
10 Nm (7.5 ftlb.) |
|
|
| Brake pressure line to hydraulic unit |
Cap screw, M14 x 1 and M12 x 1 |
Tightening torque |
16 Nm (12 ftlb.) |
|
|