Installing Cylinder Head

WARNING: This page is about a different variant/trim than selected.

Information

If cold or excessively low-tempered components are sealed to each other by applying sealant, leaks can occur because of condensed water forming or components distorting. Components must have a uniform temperature of at least 17°C.

Information

All sealing surfaces must be clean and free of grease!
It is essential to work carefully!
Tightening sequences and tightening torques must be observed!

Information

The tightening specifications for the basic engine are stored centrally.

> TECHNICAL VALUES

> 2X00IN TECHNICAL VALUES

> WM, 1001IN TIGHTENING TORQUES, TIGHTENING SEQUENCES, ASSEMBLY OVERVIEWS FOR ENGINE

Tightening torques and assembly instructions for other assemblies (e.g. chassis, electrics, transmission or body) or for peripheral engine equipment can be found in the corresponding documents.

Replace cylinder head gasket.
Place cylinder head gasket correctly, i.e. according to specifications, onto the straight pins on the engine crank housing. This must be done in such a way that the marking 'Top' is legible - see illustration- .

Courtesy of PORSCHE CARS NORTH AMERICA, INC.

Cylinder bank 1 -4

Courtesy of PORSCHE CARS NORTH AMERICA, INC.

Cylinder bank 5 - 8

Fit cylinder head. Insert cylinder head screws (screws can be re-used). For tightening specifications, see > 1001IN TIGHTENING TORQUES, TIGHTENING SEQUENCES, ASSEMBLY OVERVIEWS

Fig 1: Cylinder Head 1 To 4 Components Location

Courtesy of PORSCHE CARS NORTH AMERICA, INC.

Cylinder head 1 to 4

1	Cylinder head 1 to 4
2	Cylinder head gasket 1 to 4
3	M8 screw
4	Lid
5	Stopper
6	Stopper
7	Restrictor for valve lift adjustment
8	Cylinder head screws
9	Spark plug

Fig 2: Cylinder Head 5 To 8 Components Location

Courtesy of PORSCHE CARS NORTH AMERICA, INC.

Cylinder head 5 to 8

1	Cylinder head 5 to 8
2	Screw plug
3	Spark plug
4	Cylinder head gasket 5 to 8
5	Stopper
6	Restrictor for valve lift adjustment
7	Stopper
8	Lid
9	Cylinder head screws => For tightening specifications, see Tightening sequence for cylinder head

Fit front M8 screw to secure the cylinder head of cylinders 1 to 4 to the crankcase. -3-

Courtesy of PORSCHE CARS NORTH AMERICA, INC.

Cylinder head 1 to 4

Fit the mounting saddle at the front -8- (cylinder bank 1 to 4 shown).

Fig 3: Camshafts Components Location - Cylinder Bank 1 To 4

Courtesy of PORSCHE CARS NORTH AMERICA, INC.

Camshafts, cylinder bank 1 to 4

1	Camshaft (outlet)
2	Camshaft (intake)
3	Hydraulic valve for variable valve lift control
4	Screw, M5 x 12
5	Switching tappet (oil with engine oil)
6	Bucket tappet (oil with engine oil)
7	Stopper
8	Mounting saddle 1 to 4
9	Stopper
10	Bearing locations (oil with engine oil)
A	Direction of travel

Secure wire harness to the engine.
1. 6.1 Position and lay engine wire harness on the engine housing -arrow- .
2. 6.2 Tighten fastening screws.
Courtesy of PORSCHE CARS NORTH AMERICA, INC.

Securing engine wire harness on engine housing
Clip in engine wire harness at the rear right using the retaining clip -arrow- .

Courtesy of PORSCHE CARS NORTH AMERICA, INC.

Clipping in engine wire harness at the rear right
Clip in engine wire harness close to the vacuum pump.
1. 8.1 Clip in engine wire harness using the retaining clip -arrow A- .
2. 8.2 Slide engine wire harness onto the holder -arrow B- .
Courtesy of PORSCHE CARS NORTH AMERICA, INC.

Clipping in engine wire harness close to the vacuum pump
Clip in engine wire harness close to the high-pressure pump.
1. 9.1 Screw in and tighten the screw socket -arrow A- .
2. 9.2 Clip in engine wire harness using the retaining clips -arrows B- .
Courtesy of PORSCHE CARS NORTH AMERICA, INC.

Clipping in engine wire harness close to the high-pressure pump
Install vent line.
1. 10.1 Position vent line -1- and clip it into the cable duct -arrow- .
2. 10.2 Fit the fastening screws -2- .

Courtesy of PORSCHE CARS NORTH AMERICA, INC.

Vent line