Filling Coolant

Information 

• The amount of coolant available must be approx. 2 liters more than the amount to be filled in. 
• Because different quantities of coolant can drain away during different types of repairs, the filling capacity can vary greatly. Recommendation: To be on the safe side, fill the canister to 30 l, then bleed the cooling system. The difference after bleeding is the coolant quantity that is sucked in. Check the volume scale on the canister. 
• An antifreeze content of -35 °C corresponds to a mixture of 50: 50 (antifreeze: water). 

Information 

• The filling process is completed more quickly if the canister is positioned at roughly the same height as the coolant reservoir. 

Information 

• A hissing sound after connecting the compressed air supply is usual. 

Information 

• If no vacuum is generated (the pointer does not move to the green area), there is a leak in the cooling system. 
• If a vacuum is still not established, there is a blockage in the tool. Clean the device, use clean compressed air. 
• Deformation of the rubber hoses of the cooling system is normal. 
• Pressure of between 6 and 10 bar must be present. The higher the pressure, the better the vacuum in the vehicle cooling system. 
• When the pressure gauge pointer is in the green area of the display scale, a sufficient vacuum has been built up. 
• After both shutoff valves on the vacuum pressure gauge have been closed and the compressed air supply has been disconnected, the vacuum must not drop. If the vacuum drops within approx. 30 seconds, there is a leak in the coolant circuit. 

1. Return lines
2. Overflow container (bucket or canister)
3. Compressed air connection
4. Compressed air connection (Pressure of between 6 and 10 bar must be present. The higher the pressure, the better the vacuum in the vehicle cooling system.)
5. Filling canister with coolant (it is best to position the canister higher than the reservoir).
6. Adapter K 65 (Fitted instead of the cap on the coolant expansion tank.). General illustration provided here. Use an intermediate cable/extension (FZ 100).
7. KVB 01 (Vacuum gauge with two shut-off valves V1 and V2)

1. V1  - Shut-off valve V1 (Shutoff valve for the filler hose.)
2. -V2-  - Shut-off valve V2 (Shutoff valve for the filler hose - outlet to Venturi nozzle.)
   Fig 1: Overview Of Vacuum-Filling Device Setup

   Courtesy of PORSCHE CARS NORTH AMERICA, INC.

1. If you have not already done so, screw cap adapter K65 for coolant expansion tank onto the reservoir.
2. Connect the flexible extension (FZ 100) to the cap.
3. Connect the vacuum gauge of the bleeder tool to the flexible extension. When doing so, ensure that both shut-off valves are closed (positioned at 90° with respect to flow direction).
4. Connect the Venturi nozzle to the vacuum gauge.
5. Place a canister with a sufficient amount of coolant and with an antifreeze content of -35 °C beside the vehicle close to the reservoir.
6. Push the filler hose of the vacuum gauge onto the canister connection. Route the return line from the Venturi nozzle to a second container (bucket).
7. Connect the compressed air supply.
8. Open both shut-off valves on the vacuum gauge → Shut-off valve open  until the transparent filler hose is completely filled with coolant.
   Fig 2: Identifying Shut-Off Valve Open

   Courtesy of PORSCHE CARS NORTH AMERICA, INC.
9. Close the left shutoff valve (V1) → Closing shut-off valve on filler hose  on the vacuum gauge and allow a vacuum to build up in the coolant circuit.
   Fig 3: Identifying Closing Left Shut-Off Valve On Filler Hose

   Courtesy of PORSCHE CARS NORTH AMERICA, INC.
10. When there is a sufficient vacuum in the cooling system (pointer is in the green area) → Vacuum built up (pointer in green area)  , close the right shut-off valve (V2) and then disconnect the compressed air supply.
    Fig 4: Creating Vacuum Cooling System (Pointer In Green Area)

    Courtesy of PORSCHE CARS NORTH AMERICA, INC.
11. Open the left shut-off valve (V1) on the vacuum gauge again. The cooling system is then filled. → Filling the cooling system - opening shut-off valve for filler hose 
    Fig 5: Filling Cooling System - Opening Shut-Off Valve For Filler Hose

    Courtesy of PORSCHE CARS NORTH AMERICA, INC.
12. When there is no trace of vacuum present or the coolant is no longer drawn from the canister, open the right shut-off valve (V2). → Opening right shut-off valve 
    Fig 6: Identifying Right Shut-Off Valve Opening

    Courtesy of PORSCHE CARS NORTH AMERICA, INC.
13. Then remove the complete filling tool (including the adapter K65).
14. If necessary, fill the coolant reservoir with coolant up to the maximum marking.
15. Start the engine and leave it running at idle speed. Move the selector lever to position "P" and allow the engine to warm up.
16. Switch on passenger compartment heating. Blower setting: one bar.
    Fig 7: Locating Heater Control In Passenger Compartment

    Courtesy of PORSCHE CARS NORTH AMERICA, INC.
17. Press the "Sport button". Activate "Sport" mode during the bleeding process.
18. Check the following while the vehicle is warming up.
    1. 18.1. Coolant temperature -2-  and engine oil temperature -1-  in the instrument cluster. Figure shows normal, acceptable values.
       Fig 8: Checking Temperature In Instrument Cluster

       Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    2. 18.2. Feel the following coolant hoses to check that they are heating up uniformly. → Supply and return line for the radiator  → Peripheral engine cooling hoses 
       Fig 9: Locating Supply And Return Line For Radiator

       Courtesy of PORSCHE CARS NORTH AMERICA, INC.
       Fig 10: Locating Engine Cooling Hoses

       Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    3. 18.3. It should be possible to force any suspected air bubbles through the cooling system by pressing the accelerator pedal from idle speed to approx. 3, 500 rpm -3-  during the warm-up phase. Never supply power to the map-controlled thermostat using the workshop tester.
       Fig 11: Checking Temperature In Instrument Cluster

       Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    4. 18.4. The cooling system has been filled and bled correctly if =>
       • All coolant hoses are uniformly warm.
       • The temperature display in the instrument cluster is in the normal range.
       • The passenger compartment heater is warm.
       • The electric fan for engine cooling comes on.

Information 

• The amount of coolant available must be approx. 2 liters more than the amount to be filled in. 
• Because different quantities of coolant can drain away during different types of repairs, the filling capacity can vary greatly. Recommendation: To be on the safe side, fill the canister to 30 l, then bleed the cooling system. The difference after bleeding is the coolant quantity that is sucked in. Check the volume scale on the canister. 
• An antifreeze content of -35 °C corresponds to a mixture of 50: 50 (antifreeze: water). 

Information 

• The filling process is completed more quickly if the canister is positioned at roughly the same height as the coolant reservoir. 

Information 

• A hissing sound after connecting the compressed air supply is usual. 

Information 

• If no vacuum is generated (the pointer does not move to the green area), there is a leak in the cooling system. 
• If a vacuum is still not established, there is a blockage in the tool. Clean the device, use clean compressed air. 
• Deformation of the rubber hoses of the cooling system is normal. 
• Pressure of between 6 and 10 bar must be present. The higher the pressure, the better the vacuum in the vehicle cooling system. 
• When the pressure gauge pointer is in the green area of the display scale, a sufficient vacuum has been built up. 
• After both shutoff valves on the vacuum pressure gauge have been closed and the compressed air supply has been disconnected, the vacuum must not drop. If the vacuum drops within approx. 30 seconds, there is a leak in the coolant circuit. 

1. Return lines
2. Overflow container (bucket or canister)
3. Compressed air connection
4. Compressed air connection (Pressure of between 6 and 10 bar must be present. The higher the pressure, the better the vacuum in the vehicle cooling system.)
5. Filling canister with coolant (it is best to position the canister higher than the reservoir).
6. Adapter K 65 (Fitted instead of the cap on the coolant expansion tank.). General illustration provided here. Use an intermediate cable/extension (FZ 100).
7. KVB 01 (Vacuum gauge with two shut-off valves V1 and V2)

1. V1  - Shut-off valve V1 (Shutoff valve for the filler hose.)
2. -V2-  - Shut-off valve V2 (Shutoff valve for the filler hose - outlet to Venturi nozzle.)
   Fig 1: Identifying Vacuum-Filling Device Setup

   Courtesy of PORSCHE CARS NORTH AMERICA, INC.

1. If you have not already done so, screw cap adapter K65 for coolant expansion tank onto the reservoir.
2. Connect the flexible extension (FZ 100) to the cap.
3. Connect the vacuum gauge of the bleeder tool to the flexible extension. When doing so, ensure that both shut-off valves are closed (positioned at 90° with respect to flow direction).
4. Connect the Venturi nozzle to the vacuum gauge.
5. Place a canister with a sufficient amount of coolant and with an antifreeze content of -35 °C beside the vehicle close to the reservoir.
6. Push the filler hose of the vacuum gauge onto the canister connection. Route the return line from the Venturi nozzle to a second container (bucket).
7. Connect the compressed air supply.
8. Open both shut-off valves on the vacuum gauge → Shut-off valve open  until the transparent filler hose is completely filled with coolant.
   Fig 2: Identifying Shut-Off Valve Open

   Courtesy of PORSCHE CARS NORTH AMERICA, INC.
9. Close the left shutoff valve (V1) → Closing shut-off valve on filler hose  on the vacuum gauge and allow a vacuum to build up in the coolant circuit.
   Fig 3: Closing Shut-Off Valve On Filler Hose

   Courtesy of PORSCHE CARS NORTH AMERICA, INC.
10. When there is a sufficient vacuum in the cooling system (pointer is in the green area) → Vacuum built up (pointer in green area)  , close the right shut-off valve (V2) and then disconnect the compressed air supply.
    Fig 4: Creating Vacuum In Cooling System

    Courtesy of PORSCHE CARS NORTH AMERICA, INC.
11. Open the left shut-off valve (V1) on the vacuum gauge again. The cooling system is then filled. → Filling the cooling system - opening shut-off valve for filler hose 
    Fig 5: Filling Cooling System - Opening Shut Off Valve For Filler Hose

    Courtesy of PORSCHE CARS NORTH AMERICA, INC.
12. When there is no trace of vacuum present or the coolant is no longer drawn from the canister, open the right shut-off valve (V2). → Opening right shut-off valve 
    Fig 6: Identifying Right Shut-Off Valve (Opening)

    Courtesy of PORSCHE CARS NORTH AMERICA, INC.
13. Then remove the complete filling tool (including the adapter K65).
14. If necessary, fill the coolant reservoir with coolant up to the maximum marking.
15. Start the engine and leave it running at idle speed. Move the selector lever to position "P" and allow the engine to warm up.
16. Switch on passenger compartment heating. Blower setting: one bar.
    Fig 7: Locating Heater Control In Passenger Compartment

    Courtesy of PORSCHE CARS NORTH AMERICA, INC.
17. Press the "Sport button". Activate "Sport" mode during the bleeding process.
18. Check the following while the vehicle is warming up.
    1. 18.1. Coolant temperature -2-  and engine oil temperature -1-  in the instrument cluster. Figure shows normal, acceptable values.
       Fig 8: Checking Temperature In Instrument Cluster

       Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    2. 18.2. Feel the following coolant hoses to check that they are heating up uniformly. → Supply and return line for the radiator  → Peripheral engine cooling hoses 
       Fig 9: Locating Supply And Return Line For Radiator

       Courtesy of PORSCHE CARS NORTH AMERICA, INC.
       Fig 10: Peripheral Engine Cooling Hoses

       Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    3. 18.3. It should be possible to force any suspected air bubbles through the cooling system by pressing the accelerator pedal from idle speed to approx. 3, 500 rpm -3-  during the warm-up phase. Never supply power to the map-controlled thermostat using the workshop tester.
       Fig 11: Checking Temperature In Instrument Cluster

       Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    4. 18.4. The cooling system has been filled and bled correctly if =>
       • All coolant hoses are uniformly warm.
       • The temperature display in the instrument cluster is in the normal range.
       • The passenger compartment heater is warm.
       • The electric fan for engine cooling comes on.