| Steering gear to subframe |
M12 x 1.5 thread |
Tightening torque |
90 Nm (67 ftlb.) |
+150° |
|
| Retainer plate for steering lines to steering gear |
M10 x 20 thread |
Tightening torque |
20 Nm (15 ftlb.) |
|
|
| Axial joint to rack-and-pinion |
M16 x 1.5 thread |
Tightening torque |
140 Nm |
|
|
| Tie rod to axial joint |
M14 x 1.5 thread |
Tightening torque |
70 Nm (52 ftlb.) |
|
|
| Tie-rod ball to tapered end of wheel carrier |
M12 x 1.5 thread |
Tightening torque |
85 Nm (63 ftlb.) |
|
|
| Universal joint to steering gear |
M8 x 30 thread |
Tightening torque |
20 Nm (15 ftlb.) |
+90° |
|
| Heat shield to steering gear |
M6 x 12 thread |
Tightening torque |
10 Nm (7.5 ftlb.) |
|
|
| Steering return line to mount for front-axle supporting frame, front |
M6 x 12 thread |
Tightening torque |
10 Nm (7.5 ftlb.) |
|
|
| Steering return line to mount for front-axle supporting frame, center |
M6 x 12 thread |
Tightening torque |
10 Nm (7.5 ftlb.) |
|
|
| Steering return line to mount for front-axle supporting frame, rear |
M6 x 12 thread |
Tightening torque |
10 Nm (7.5 ftlb.) |
|
|
| Steering return line mount to holder for carrier 1 in wheel housing |
|
Tightening torque |
0.8 Nm (0.5 ftlb.) |
|
|
| Steering return line to mount for holder for carrier 1 in wheel housing |
M6 x 12 thread |
Tightening torque |
10 Nm (7.5 ftlb.) |
|
|
| Mount for steering pressure pipe to steering gear |
|
Tightening torque |
1 Nm (0.5 ftlb.) |
|
|
| Steering pressure pipe to mount for steering gear |
M6 thread |
Tightening torque |
10 Nm (7.5 ftlb.) |
|
|
| Mount for steering pressure pipe to valve tower for steering gear |
|
Tightening torque |
1 Nm (0.5 ftlb.) |
|
|
| Steering pressure pipe to valve tower for steering gear |
M6 x 12 thread |
Tightening torque |
10 Nm (7.5 ftlb.) |
|
|
| Steering return line to crash support |
M6 x 12 |
Tightening torque |
10 Nm (7.5 ftlb.) |
|
|
| Steering pressure pipe to air conditioning compressor |
M5 x 10 thread |
Tightening torque |
6 Nm (4.5 ftlb.) |
|
|
| Steering return line to steering gear, RHD |
M6 x 16 thread |
Tightening torque |
10 Nm (7.5 ftlb.) |
|
|
| Retainer plate for steering lines to steering gear |
M10 x 20 thread |
Tightening torque |
20 Nm (15 ftlb.) |
|
|
| Hydraulic pump to front bracket (3 x Torx) |
M8 thread |
Tightening torque |
23 Nm (17 ftlb.) |
|
|
| Hydraulic pump to rear bracket (3 x Torx) |
M8 x 20 thread |
Tightening torque |
23 Nm (17 ftlb.) |
|
|
| Steering pressure line to hydraulic pump (union nut) |
Without PDCC |
Tightening torque |
32 Nm |
|
|
| Pulley to hydraulic pump |
Thread |
Tightening torque |
25 Nm (19 ftlb.) |
|
|
| Hydraulic pump to front bracket (3 x Torx) |
M8 thread |
Tightening torque |
23 Nm (17 ftlb.) |
|
|
| Hydraulic pump to rear bracket (3 x Torx) |
M8 x 20 thread |
Tightening torque |
23 Nm (17 ftlb.) |
|
|
| Steering expansion hose to hydraulic pump (banjo bolt) |
With PDCC |
Tightening torque |
35 Nm (26 ftlb.) |
|
|
| Steering (tandem) intake pipe to hydraulic pump (nut) |
With PDCC |
Tightening torque |
10 Nm (7.5 ftlb.) |
|
|
| Pulley to hydraulic pump |
Thread |
Tightening torque |
25 Nm (19 ftlb.) |
|
|
| Hydraulic pump to front bracket (2 x internal serration screw) |
M8 x 32 thread |
Tightening torque |
23 Nm (17 ftlb.) |
|
|
| Hydraulic pump to rear bracket (1 x internal serration screw) |
M8 x 32 thread |
Tightening torque |
23 Nm (17 ftlb.) |
|
|
| Steering pressure line to hydraulic pump |
M6 x 16 thread |
Tightening torque |
10 Nm (7.5 ftlb.) |
|
|
| Pulley to hydraulic pump |
Thread |
Tightening torque |
25 Nm (19 ftlb.) |
|
|
| Hydraulic pump to chassis subframe |
M8 thread |
Tightening torque |
20 Nm |
|
|
| Hydraulic pump to holder |
M6 x 12 thread |
Tightening torque |
10 Nm (7.5 ftlb.) |
|
|
| Pressure line to hydraulic pump |
M8 x 20 thread |
Tightening torque |
20 Nm |
|
|
| Steering column to retaining frame |
M8 x 30 thread |
Tightening torque |
20 Nm (15 ftlb.) |
|
|
| Steering wheel to steering column |
Multiple-tooth screw M18 x 1.5 x 26, always replace following removal! (micro-encapsulated thread) |
Tightening torque + torque angle |
30 Nm (22 ftlb.) |
+90° |
|
| Handle to control lever |
M5 x 8 thread |
Tightening torque |
3 Nm (2 ftlb.) |
|
|
| Retaining bracket to retaining frame |
M5 x 20 thread |
Tightening torque |
3 Nm |
|
|