| Threaded connection securing brake pressure line to brake master cylinder, M12 x 1 |
Tightening torque was increased to 25 Nm/19 ftlb. (also applies to older vehicles). Counter using special tool 9763 while tightening |
Tightening torque |
25 Nm (19 ftlb.) |
|
|
| Threaded connection securing brake pressure line to hydraulic unit, M12 x 1 |
Tightening torque was increased to 25 Nm/19 ftlb. (also applies to older vehicles) |
Tightening torque |
25 Nm (19 ftlb.) |
|
|
| Threaded connection securing brake pressure line to hydraulic unit, M10 x 1 |
|
Tightening torque |
16 Nm (12 ftlb.) |
|
|
| Threaded connection securing brake pressure line to distributor, brake hose and brake calliper, M10 x 1 |
|
Tightening torque |
16 Nm (12 ftlb.) |
|
|
| Threaded connection securing brake pressure line to intermediate piece, M10 x 1 |
Centre underbody |
Tightening torque |
16 Nm (12 ftlb.) |
|
|
| Threaded connection securing brake pressure line to intermediate piece, M12 x 1 |
Centre underbody |
Tightening torque |
25 Nm (19 ftlb.) |
|
|
| Threaded connection securing brake booster to body, M8 |
|
Tightening torque |
23 Nm (17 ftlb.) |
|
|
| Threaded connection securing brake unit support to body, M8 |
|
Tightening torque |
23 Nm (17 ftlb.) |
|
|
| Threaded connection securing brake master cylinder to brake booster, M14 |
|
Tightening torque |
49 Nm (36 ftlb.) |
|
|
| Threaded connection securing brake pressure line to brake master cylinder, M12 x 1 |
Tightening torque was increased to 25 Nm/19 ftlb. (also applies to older vehicles). Counter using special tool 9763 while tightening |
Tightening torque |
25 Nm (19 ftlb.) |
|
|
| Threaded connection securing bracket for hydraulic unit to body, M6 |
|
Tightening torque |
4 Nm (3 ftlb.) |
|
|
| Threaded connection securing hydraulic unit to bracket, M6 |
|
Tightening torque |
5.5 Nm (4 ftlb.) |
|
|
| Threaded connection securing brake pressure line to hydraulic unit, M10 x 1 |
|
Tightening torque |
16 Nm (12 ftlb.) |
|
|
| Threaded connection securing brake pressure line to hydraulic unit, M12 x 1 |
|
Tightening torque |
25 Nm (19 ftlb.) |
|
|
| Threaded connection securing brake calliper to wheel carrier, M12 x 1.5 |
Replace screws on front and rear axle whenever removed. |
Tightening torque |
85 Nm (63 ftlb.) |
|
|
| Threaded connection securing brake pressure line to brake calliper, M10 x 1 |
|
Tightening torque |
16 Nm (12 ftlb.) |
|
|
| Threaded connection securing connecting line to brake calliper, M10 x 1 |
|
Tightening torque |
12 Nm (9 ftlb.) |
|
|
| Threaded connection securing bleeder screw to brake calliper, M10 x 1 |
|
Tightening torque |
8-12 Nm (6 -9 ftlb.) |
|
|