LEMON Manuals: Even more car manuals for everyone
Home >> Porsche >> 2011 >> Panamera Turbo >> Repair and Diagnosis >> Drivelines & Axles >> Wheel Hubs >> 42 - Rear Wheel Suspension, Drive Shafts -- PANAMERA (970) >> WM 422119 Removing And Installing Rear Drive Shaft (Except PANAMERA GTS, PANAMERA Turbo S, PANAMERA Platinum Ed., PANAMERA 4 Platinum Ed.) >> Removing And Installing Rear Drive Shaft >> Removing Rear Drive Shaft

Removing Rear Drive Shaft

Fig 1: Locating Rear Drive Shaft
G09807576Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  1. Release and unclip the connector for the brake pad wear indicator -A-  and remove it from the holder -B-  .
    Fig 2: Removing Brake Pad Wear Indicator From Holder
    G09807577Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  2. Loosen fastening screw -1-  on the holder for the brake pad wear indicator cable and brake line from the brake calliper.
    Fig 3: Loosening Brake Line Holder Fastening Screw
    G09807578Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    NOTE: Removing/fitting wheels
    • Risk of damage to (ceramic) brake discs

    → Carefully guide the wheel towards the wheel hub, thereby preventing any heavy impact on the (ceramic) brake disc.

  3. Evenly set back brake pads a little using water pump pliers.

    Information 

    • Never use an impact bolter to loosen and tighten the brake calliper on the wheel bearing housing. 
  4. Loosen fastening screws on the brake calliper -arrows-  and remove brake calliper from the wheel carrier.
    Fig 4: Loosening Brake Calliper Fastening Screws
    G09807579Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  5. Suspend the brake calliper at a suitable position in the wheel housing (do not open the brake hydraulic system!).
  6. Disconnect push-on connector -1-  and detach bracket -2-  from the wheel carrier.
    Fig 5: Disconnecting Connector And Bracket From Wheel Carrier
    G09807580Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  7. Disengage linkage -1-  for the level sensor at the ball pin -2-  .
    Fig 6: Disengaging Level Sensor At Ball Pin
    G09807581Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  8. Puller set Nr.87-1 Pos.1 -1-  must be fitted on the brake disc.
    Fig 7: Identifying Puller Set On Brake Disc
    G09807582Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  9. Support wheel carrier using a suitable lever -2-  on the outside in order to prevent the wheel carrier from tipping over.
    Fig 8: Supporting Wheel Carrier
    G09807583Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  10. Screw in spindle -4- → Control value: +10 mm  (-arrow-  ).
  11. Unscrew and remove fastening screws -3-  for the upper trailing arms and tie rod.
  12. Lower the lever -2-  slowly.
    1. 12.1. While tilting the wheel carrier with the spindle -4-  , press the drive shaft back as far as required until it can be removed from the hub.
  13. Remove lever -2-  .
  14. Tilt wheel carrier -1-  downwards. Get a second fitter to hold the drive shaft -2-  .
    Fig 9: Tilting Wheel Carrier
    G09807584Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  15. Protect drive shaft using a suitable plastic tube and carefully set it down on the chassis subframe while performing the following work.
    Fig 10: Example Of Protective Tube
    G09807585Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  16. Left side: Break off protective plastic ring -1-  with a screwdriver.
    Fig 11: Breaking Protective Plastic Ring
    G09807586Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  17. Lever the drive shaft out of the rear-axle transmission housing using two mounting levers, for example.
    IMPORTANT: Hold the drive shaft!  In the event of unfavorable tolerances, the drive shaft might slip out.
    Fig 12: Fitting Mounting Levers
    G09807587Courtesy of PORSCHE CARS NORTH AMERICA, INC.
scientia non olet · About LEMON Manuals