LEMON Manuals: Even more car manuals for everyone
Home >> Porsche >> 2011 >> 911 Speedster >> Repair and Diagnosis >> Body & Frame >> Exterior/Interior Trim >> 66 - Exterior Equipment -- CARRERA (997) >> WM 665819 Removing And Installing Rear Spoiler (911 Turbo Coupe, 911 Turbo S Coupe, 911 Turbo S Coupe "Ed. 918 SPYDER", 911 Turbo CABRIO, 911 Turbo S CABRIO, 911 Gt2, 911 Gt2 RS) >> Removing Rear Spoiler >> Removing Rear Spoiler (With Spoiler Drive Intact)

Removing Rear Spoiler (With Spoiler Drive Intact)

Fig 1: Identifying Rear Spoiler Position
G09826787Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  1. Extend the rear spoiler.
    1. 1.1. Switch on ignition.
    2. 1.2. Extend rear spoiler -1-  manually using the rocker switch.
      Fig 2: Removing Rear Spoiler
      G09826788Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  2. Place rear spoiler in service position.
    1. 2.1. P 9751  Assembly aid -2-  must be folded and inserted in the middle between the rear lid and the rear spoiler -1-  .
    2. 2.2. Assembly aid P 9751 -2-  must be pumped up carefully using the → tire-inflating device V.A.G 1225  until the gap -X-  between the rear lid and the rear spoiler is -1-  approx. 100 mm.
      3. Fig 3: Pulling Out Rear Spoiler
      G09826789Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  3. Loosen rear spoiler at the left and right hydraulic cylinders.
    1. 3.1. Turn outer pipe -3-  using the socket-wrench insert P 9752 -4-  until the bore -arrow-  on the outer pipe -3-  is directly covering the bore on the mount -2-  .
      Fig 4: Aligning Bores On Hydraulic Cylinder
      G09826790Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    2. 3.2. Socket-wrench insert P 9752 -4-  must be inserted into the bores on the outer pipe -3-  and on the mount -2-  , and the mount -2-  on both hydraulic cylinders must then be screwed out of the rear spoiler -1-  by turning it max. 5 times in a clockwise direction.
      Fig 5: Removing Hydraulic Cylinder Of Rear Spoiler
      G09826791Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    3. 3.3. Vent air from the assembly aid P 9751  slowly and remove assembly aid P 9751  from between the rear lid and rear spoiler.
    4. 3.4. Unscrew mount -2-  at both hydraulic cylinders completely out of the rear spoiler -1-  by hand and lift up the rear spoiler -1-  .
      Fig 6: Lifting Up Rear Spoiler
      G09826792Courtesy of PORSCHE CARS NORTH AMERICA, INC.


Fig 1: Identifying Rear Spoiler Position
G09826793Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  1. Extend rear spoiler.
    1. 1.1. Switch on ignition.
    2. 1.2. Extend rear spoiler -1-  manually using the rocker switch.
      3. Fig 2: Removing Rear Spoiler
      G09826794Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  2. Loosen rear spoiler at the left and right hydraulic cylinders.
    1. 2.1. Turn outer pipe -3-  using the socket-wrench insert 9752 -4-  until the bore -arrow-  on the outer pipe -3-  is directly covering the bore on the mount -2-  .
      Fig 3: Aligning Bores On Hydraulic Cylinder
      G09826795Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    2. 2.2. Socket-wrench insert 9752 -4-  must be inserted into the bores on the outer pipe -3-  and on the mount -2-  , and the mount -2-  on both hydraulic cylinders must then be screwed out of the rear spoiler -1-  by turning it max. 5 times in a clockwise direction.
      Fig 4: Removing Hydraulic Cylinder Of Rear Spoiler
      G09826796Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    3. 2.3. Unscrew mount -2-  at both hydraulic cylinders completely out of the rear spoiler -1-  by hand and lift up the rear spoiler -1-  .
      Fig 5: Lifting Up Rear Spoiler
      G09826797Courtesy of PORSCHE CARS NORTH AMERICA, INC.


Fig 1: Identifying Rear Spoiler Position
G09826938Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  1. Extend the rear spoiler.
    1. 1.1. Switch on ignition.
    2. 1.2. Extend rear spoiler -1-  manually using the rocker switch.
      3. Fig 2: Removing Rear Spoiler
      G09826939Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  2. Place rear spoiler in service position.
    Fig 3: Pulling Out Rear Spoiler
    G09826940Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    1. 2.1. P 9751 Assembly aid -2-  must be folded and inserted in the middle between the rear lid and the rear spoiler -1-  .
    2. 2.2. Assembly aid P 9751 -2-  must be pumped up carefully using the → tire-inflating device V.A.G 1225  until the gap -X-  between the rear lid and the rear spoiler is -1-  approx. 100 mm.
  3. Loosen rear spoiler at the left and right hydraulic cylinders.
    1. 3.1. Turn outer pipe -3-  using the socket-wrench insert P 9752 -4-  until the bore -arrow-  on the outer pipe -3-  is directly covering the bore on the mount -2-  .
      Fig 4: Aligning Bores On Hydraulic Cylinder
      G09826941Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    2. 3.2. Socket-wrench insert P 9752 -4-  must be inserted into the bores on the outer pipe -3-  and on the mount -2-  , and the mount -2-  on both hydraulic cylinders must then be screwed out of the rear spoiler -1-  by turning it max. 5 times in a clockwise direction.
      Fig 5: Removing Hydraulic Cylinder Of Rear Spoiler
      G09826942Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    3. 3.3. Vent air from the assembly aid P 9751  slowly and remove assembly aid P 9751  from between the rear lid and rear spoiler.
    4. 3.4. Unscrew mount -2-  at both hydraulic cylinders completely out of the rear spoiler -1-  by hand and lift up the rear spoiler -1-  .
      Fig 6: Lifting Up Rear Spoiler
      G09826943Courtesy of PORSCHE CARS NORTH AMERICA, INC.
scientia non olet · About LEMON Manuals