| Brake calliper to wheel carrier front |
M16 x 1.5 thread (always replace screws and lock nuts after removal) |
Tightening torque |
270 Nm (200 ftlb.) |
|
|
| Brake calliper to rear wheel carrier |
M14 x 1.5 thread (always replace screws and lock nuts after removal) |
Tightening torque |
180 Nm (133 ftlb.) |
|
|
| Fastening screw securing brake calliper to wheel hub (front and rear axle) |
M12 x 1.5 thread (always replace screws and lock nuts after removal) |
Tightening torque |
14 Nm (10.5 ftlb.) |
|
|
| Plug for rear brake disc |
M12 x 1.5 x 5.5 thread |
Tightening torque |
14 Nm (10.5 ftlb.) |
|
|
| Brake cover plate to front axle |
M8 x 12 thread |
Tightening torque |
20 Nm (15 ftlb.) |
|
|
| Calliper carrier to rear wheel carrier |
M8 x 16 thread |
Tightening torque |
10 Nm (15 ftlb.) |
|
|
| Calliper carrier to rear wheel carrier |
M6 x 12 thread |
Tightening torque |
8 Nm (6.0 ftlb.) |
|
|
| Retaining pin for front brake pads |
M8 x 15 thread (always replace retaining pin) |
Tightening torque |
30 Nm (22 ftlb.) |
+/-2 Nm (+/-1.5 ftlb.) |
|
| Speed sensor to front and rear axles |
M6 x 16 thread |
Tightening torque |
8 Nm (6.0 ftlb.) |
|
|
| Brake hose holder to front-axle wheel carrier |
M6 x 12 thread |
Tightening torque |
9 Nm (6.5 ftlb.) |
|
|
| Cable holder to front-axle wheel carrier |
M8 x 14 thread |
Tightening torque |
30 Nm (22 ftlb.) |
|
|
| Brake booster |
M8 thread |
Tightening torque |
26 Nm (19 ftlb.) |
+/-3 Nm (+/-2.0 ftlb.) |
|
| Mount for hydraulic unit support |
M6 x 10 thread |
Tightening torque |
10 Nm (7.5 ftlb.) |
|
|
| Mount for intermediate piece |
M6 x 14 thread |
Tightening torque |
10 Nm (7.5 ftlb.) |
|
|
| Foot-operated parking brake pedal to mounting bracket |
M8 x 40 thread |
Tightening torque |
23 Nm (17 ftlb.) |
|
|
| Foot-operated parking brake pedal to mounting bracket |
M8 x 16 thread |
Tightening torque |
23 Nm (17 ftlb.) |
|
|
| Deflector to body (tunnel) |
M8 x 20 thread |
Tightening torque |
23 Nm (17 ftlb.) |
|
|
| Pedals (pedal block) to firewall |
M8 x 20 thread |
Tightening torque |
23 Nm (17 ftlb.) |
+/-3 Nm (+/-2.0 ftlb.) |
|
| Clutch master cylinder to pedal block |
M6 x 25 thread |
Tightening torque |
10 Nm (7.5 ftlb.) |
+/-1.5 Nm (+/-1.0 ftlb.) |
|
| Screws for articulated strut to pedal bearing block |
|
Tightening torque |
10 Nm (7.5 ftlb.) |
+/-1.5 Nm (+/-1.0 ftlb.) |
|
| Brake lever shaft bolt (inserted from right to left) |
M8 thread |
Tightening torque |
20 Nm (15 ftlb.) |
+/-3 Nm (+/-2.0 ftlb.) |
|
| Clip (holder) for brake light switch |
|
Tightening torque |
8 Nm (6.0 ftlb.) |
+/-1 Nm (+/-0.5 ftlb.) |
|
| Accelerator pedal to pedal block |
|
Tightening torque |
10 Nm (7.5 ftlb.) |
+/-1.5 Nm (+/-1.0 ftlb.) |
|
| Wheel to wheel hub |
M14 x 1.5 thread |
Tightening torque |
160 Nm (118 ftlb.) |
|
|
| ABS cable holder to rear-axle wheel carrier |
M6 x 16 thread |
Tightening torque |
8 Nm (6.0 ftlb.) |
|
|
| Brake line holder to rear-axle brake calliper |
M6 x 12 thread |
Tightening torque |
8 Nm (6.0 ftlb.) |
|
|
| Cable holder for speed sensor/ABS to rear control arm (upper front) |
M6 thread |
Tightening torque |
8 Nm (6.0 ftlb.) |
|
|