| -1- |
Taper roller bearing |
1 |
Press off via the reverse gear wheel using a suitable separating device (e.g. Kukko 17/2). |
| -2- |
Loose gear wheel, reverse gear |
1 |
| -3- |
Synchronizer ring |
1 |
Mark for re-installation. |
| -4- |
Operating sleeve |
1 |
| -5- |
Needle-roller bearing |
1 |
Mark for re-installation. |
| -6- |
Blue circlip |
1 |
Mark for re-installation. |
| -7- |
Synchronizing hub |
1 |
Press off together with loose gear wheel for 5th gear using a suitable separating device (e.g. Kukko 17/2). |
| -8- |
Synchronizing ring, 5th gear |
1 |
Mark for re-installation. |
| -9- |
Loose gear wheel, 5th gear |
1 |
| -10- |
Brown circlip |
1 |
Mark for re-installation. |
| -11- |
Needle-roller bearing |
1 |
Mark for re-installation. |
| -12- |
Circlip |
1 |
Mark for re-installation. |
| -13- |
Fixed gear wheel, 4th gear |
1 |
Press off with pressure plate vw 402
. |
| -14- |
Circlip |
1 |
Mark for re-installation. |
| -15- |
Fixed gear wheel, 3rd gear |
1 |
Press off with pressure plate vw 402
. |
| -16- |
Loose gear wheel, 2nd gear |
1 |
| -17- |
Friction ring, 2nd gear |
1 |
Mark for re-installation. |
| -18- |
Synchronizer ring, 2nd gear |
1 |
Mark for re-installation. |
| -19- |
Operating sleeve |
1 |
| -20- |
Needle-roller bearing |
1 |
Mark for re-installation. |
| -21- |
Blue circlip |
1 |
Mark for re-installation. |
| -22- |
Blue circlip |
1 |
Mark for re-installation. |
| -23- |
Synchronizing hub |
1 |
Press off together with loose gear wheel for 1st gear using a suitable separating device (e.g. Kukko 17/2). |
| -24- |
Synchronizer ring, 1st gear |
1 |
Mark for re-installation. |
| -25- |
Cone ring, 1st gear |
1 |
Mark for re-installation. |
| -26- |
Friction ring, 1st gear |
1 |
Mark for re-installation. |
| -27- |
Loose gear wheel, 1st gear |
1 |
| -28- |
Needle-roller bearing |
1 |
Mark for re-installation. |
| -29- |
Circlip |
1 |
Mark for re-installation. |
| -30- |
Taper roller bearing |
1 |
Press off with taper roller bearing outer ring and pressure plate vw 401
and pressure plate vw 402
. |
| -31- |
Output shaft |
1 |
| -32- |
Taper roller bearing outer ring |
1 |
→ DISASSEMBLING TRANSMISSION HOUSING |
| -33- |
Adjusting shim S3 |
X |
→ DISASSEMBLING TRANSMISSION HOUSING |
| -34- |
Retaining sleeve |
1 |
→ DISASSEMBLING TRANSMISSION COVER |
| -35- |
Taper roller bearing outer ring |
1 |
→ DISASSEMBLING TRANSMISSION COVER |
| -36- |
Adjusting shim S4 |
X |
→ DISASSEMBLING TRANSMISSION COVER |
| -37- |
Pressure plate |
1 |
→ DISASSEMBLING TRANSMISSION COVER |
| -38- |
Rubber washer |
1 |
→ DISASSEMBLING TRANSMISSION COVER |
| -39- |
Transmission cover |
1 |
→ DISASSEMBLING TRANSMISSION COVER |
| -40- |
Transmission housing |
1 |
→ DISASSEMBLING TRANSMISSION HOUSING |