| Connecting rod bolts |
M9 x 1x 50 (always replace) |
Initial tightening |
30 Nm (22 ft lbs.) |
|
|
| Connecting rod bolts |
|
Torque angle |
90° |
|
|
| Cylinder-head screws (internal serration) |
M9 x 1.25 x 141 (7 ea., centre) and M9 x 1.25 x 111 (13 ea., outer), always replace |
Initial tightening |
15 Nm (11 ft lbs.) |
|
|
| Cylinder-head screws (internal serration) |
|
Tightening torque |
30 Nm (22 ft lbs.) |
|
|
| Cylinder-head screws (internal serration) |
|
Torque angle |
180° |
|
|
| Oval-head screw on timing chain housing |
M6 x 25 |
Tightening torque |
8 Nm (6 ft lbs.) |
|
|
| Hexagon-head bolts on oil pump |
M8 x 20 |
Tightening torque |
8 Nm (6 ft lbs.) |
|
|
| Chain tensioner |
M22 x 1.5 x 18.7 |
Tightening torque |
40 Nm (30 ft lbs.) |
|
|
| Bearing pin on guide rail for drive chain |
M8 x 11.5 |
Tightening torque |
10 Nm (7.5 ft lbs.) |
|
|
| Hexagon-head bolt on drive wheel for timing chain |
M10 x 40 (always replace) |
Initial tightening |
60 Nm (44 ft lbs.) |
|
|
| Hexagon-head bolt on drive wheel for timing chain |
|
Torque angle |
90° |
|
|
| Bolt for guide rail |
|
Tightening torque |
10 Nm (7.5 ft lbs.) |
|
|
| Fastening screw on guide rail |
|
Tightening torque |
20 Nm (15 ft lbs.) |
|
|
| Hexagon-head bolt on guide rail |
M8 x 45 |
Tightening torque |
23 Nm (17 ft lbs.) |
|
|
| Hexagon-head bolts on camshaft controllers |
M12 x 1.5 x 85 (always replace) |
Initial tightening |
60 Nm (44 ft lbs.) |
|
|
| Hexagon-head bolts on camshaft controllers |
|
Torque angle |
90° |
|
|
| Hexagon-head bolt on lower timing-case cover |
M6 x 16 (20 ea.); M6 x 58 (2 ea.) |
Tightening torque |
10 Nm (7.5 ft lbs.) |
|
|
| Oval-head screw on vacuum pump |
M6 x 20 |
Tightening torque |
8 Nm (6 ft lbs.) |
|
|
| Oval-head screw on vacuum pump |
M6 x 40 |
Tightening torque |
8 Nm (6 ft lbs.) |
|
|
| Hexagon-head bolts on oil pan |
M6 x 20 |
Tightening torque |
12 Nm (9 ft lbs.) |
|
|
| Fastening screw on cylinder head cover |
With guide sleeve |
Tightening torque |
10 Nm (7.5 ft lbs.) |
|
|
| Fuel line to fuel distribution pipe |
|
Tightening torque |
22 Nm (16 ft lbs.) |
|
|
| Fuel line at plenum panel |
|
Tightening torque |
35 Nm (26 ft lbs.) |
|
|
| Cheese head bolts on fuel distribution pipe |
M8 x 55 (always replace) |
Initial tightening |
30 Nm (22 ft lbs.) |
|
|
| Cheese head bolts on fuel distribution pipe |
|
Torque angle |
90° |
|
|