| Components |
|
Temperature |
17°C |
|
|
| Guide tube for dipstick to oil guide housing |
M6 x 16 (1 ea.) |
Tightening torque |
10 Nm (7.5 ft lbs.) |
|
|
| Timing-case cover to oil guide housing |
M6 x 30; always use new aluminium screws |
Initial tightening |
4 Nm (3 ft lbs.) |
|
|
| Timing-case cover to oil guide housing |
M6 x 30; always use new aluminium screws |
Final tightening |
90° |
|
|
| Oil-level sensor to oil guide housing |
|
Tightening torque |
12 Nm (9 ft lbs.) |
|
|
| Oil guide housing to lower part of crankcase |
M6 x 30; always use new aluminium screws |
Initial tightening |
4 Nm (3 ft lbs.) |
|
|
| Oil guide housing to lower part of crankcase |
M6 x 30; always use new aluminium screws |
Final tightening |
90° |
|
|
| Joint flange to oil guide housing |
M6 x 20 (2 ea.) |
Tightening torque |
10 Nm (7.5 ft lbs.) |
|
|
| Guide tube for dipstick to timing-case cover |
M6 x 16 (1 ea.) |
Tightening torque |
10 Nm (7.5 ft lbs.) |
|
|
| Oil pressure pipe to oil pump and oil guide housing |
M6 x 16 (3 ea.) |
Tightening torque |
12 Nm (9 ft lbs.) |
|
|
| Oil control line to oil pump and oil guide housing |
M6 x 16 (2 ea.) |
Tightening torque |
12 Nm (9 ft lbs.) |
|
|
| Turbocharger extraction line to oil pump |
M6 x 16 (2 ea.) M48/51 |
Tightening torque |
12 Nm (9 ft lbs.) |
|
|
| Pressure-stage intake pipe to oil pump |
M6 x 20 (2 ea.) |
Tightening torque |
12 Nm (9 ft lbs.) |
|
|
| Oil pressure pipe to oil pump and oil guide housing |
M6 x 16 (3 ea.) |
Tightening torque |
12 Nm (9 ft lbs.) |
|
|
| Oil control line to oil pump and oil guide housing |
M6 x 16 (2 ea.) |
Tightening torque |
12 Nm (9 ft lbs.) |
|
|
| Pressure-stage intake pipe to oil pump |
M6 x 20 (2 ea.) |
Tightening torque |
12 Nm (9 ft lbs.) |
|
|
| Vent line to turbocharger oil extraction line |
M16 x 1.5 (2 ea.) M48/51 |
Tightening torque |
35 Nm (26 ft lbs.) |
|
|
| Holding clamp on vent line to collection pipe |
M6 x 12 (2 ea.) M48/51 |
Tightening torque |
10 Nm (7.5 ft lbs.) |
|
|
| Holding clamp on vent line to collection pipe |
M6 (2 ea.) M48/51 |
Tightening torque |
6.5 Nm (5.0 ft lbs.) |
|
|
| Turbocharger oil feed line to connection piece |
M16 x 1.5 (2 ea.) M48/51 |
Tightening torque |
40 Nm (30 ft lbs.) |
|
|
| Turbocharger oil feed line to cylinder head |
M14 x 1.5 (2 ea.) M48/51 |
Tightening torque |
35 Nm (26 ft lbs.) |
|
|
| Check valve connection piece to turbocharger |
M12 x 1.5 (2 ea.) M48/51 |
Tightening torque |
45 Nm (33 ft lbs.) |
|
|
| Turbocharger oil extraction line to oil guide housing |
M6 x 12 (2 ea.) M48/51 |
Tightening torque |
10 Nm (7.5 ft lbs.) |
|
|
| Oil extraction line to turbocharger |
M6 x 16 (4 ea.) M48/51 |
Tightening torque |
10 Nm (7.5 ft lbs.) |
|
|
| Holding clamp on vent line to collection pipe |
M6 (2 ea.) M48/51 |
Tightening torque |
6.5 Nm (5 ft lbs.) |
|
|
| Holding clamp on vent line to collection pipe |
M6 x 12 (2 ea.) M48/51 |
Tightening torque |
10 Nm (7.5 ft lbs.) |
|
|
| Turbocharger oil feed line holder to lower part of crankcase |
M6 x 12 (1 ea.) M48/51 |
Tightening torque |
10 Nm (7.5 ft lbs.) |
|
|
| Holding clamp for oil feed line to holder |
M6 x 12 (1 ea.) M48/51 |
Tightening torque |
10 Nm (7.5 ft lbs.) |
|
|
| Oil extraction line to turbocharger |
M6 x 16 (4 ea.) M48/51 |
Tightening torque |
10 Nm (7.5 ft lbs.) |
|
|