Technical Values
| Location | Description | Type | Basic value | Tolerance 1 | Tolerance 2 |
|---|---|---|---|---|---|
| Front lid to front apron (B) | Gap dimension | 4 mm | +1 mm | ||
| Front lid to front apron (C) | Lid only lowered (max. 1 mm) | Gap dimension | 1 mm | ||
| Main headlight to side of front apron (D) | Gap dimension | 4 mm | +/-1.2 mm | ||
| Direction indicator light to front apron (H) | Gap is evident | Gap dimension | 1 mm | ||
| Front apron to wing (G) | Gap is evident | Gap dimension | 0.5 mm | +/-0.5 mm | |
| Headlight washer system lid to front apron (J) | All the way round | Gap dimension | 1 mm | ||
| Fog light to front apron (K) | All the way round | Gap dimension | 4 mm | -0.5 mm | +1.5 mm |
| Main headlight to bottom of front apron (L) | Gap dimension | 4 mm | +/-1.0 mm | ||
| Insignia to front apron (M) | Equal all the way round | Gap dimension | 1.25 mm | +/-0.4 mm | |
| Front door to front wing (N) | Front door only lowered (max. 1 mm) | Gap dimension | 4.5 mm | +0.7 mm -0.5 mm | |
| Front wing to A-pillar (O) | Gap dimension | 2 mm | -0.5 mm | +1 mm | |
| Front wing to front lid (A) | Gap dimension | 4 mm | +/-1 mm | ||
| Front apron to front wing (G) | Gap is evident | Gap dimension | 0.5 mm | +/-0.5 mm | |
| Main headlight to front lid (E) | Gap dimension | 4 mm | +/-0.5 mm | ||
| Main headlight to front wing (F) | Gap dimension | 3 mm | +/-0.5 mm | ||
| Main headlight to front wing (G) | Gap dimension | 3 mm | -1 mm | ||
| Front wing to front lid (A) | Gap dimension | 4 mm | +/-1 mm | ||
| Front lid to front apron (B) | Gap dimension | 4 mm | +1 mm | ||
| Front lid to front apron (C) | Lid only lowered (max. 1 mm) | Gap dimension | 1 mm | ||
| Main headlight to front lid (E) | Gap dimension | 4 mm | +/-0.5 mm | ||
| Main headlight to side of front apron (D) | Gap dimension | 4 mm | +/-1.2 mm | ||
| Main headlight to front lid (E) | Gap dimension | 4 mm | +/-0.5 mm | ||
| Main headlight to front wing (F) | Gap dimension | 3 mm | +/-0.5 mm | ||
| Main headlight to front wing (G) | Gap dimension | 3 mm | -1 mm | ||
| Main headlight to bottom of front apron (L) | Gap dimension | 4 mm | +/-1 mm | ||
| Mirror glass to mirror housing (M) | Gap dimension | 3 mm | |||
| Mirror housing to mirror cover (L) | Gap dimension | 2 mm | |||
| Mirror surround to roof trim strip (C) | Gap dimension | 3 mm | |||
| Windscreen to outer roof panel (A) | Gap width | Gap dimension | 3 mm | -1 mm | |
| Windscreen to outer roof panel (B) | Installation depth | Gap dimension | 4 mm | -1 mm | |
| Mirror surround to roof molding (C) | Gap dimension | 3 mm | |||
| Door window to molding and outer side section (F) | Gap dimension | 5 mm | |||
| Door cover to outer door panel (H) | Gap dimension | 4 mm | |||
| Door cover to outer door panel (J) | Gap dimension | 0.5 mm | |||
| Front door to wing (N) | Front door only lowered (max. 1 mm) | Gap dimension | 4.5 mm | +/-0.7 mm | -0.5 mm |
| Front door to rear door (K) | Rear door only lowered (max. 1 mm) | Gap dimension | 4.5 mm | +/-0.7 mm | -0.5 mm |
| Front door molding to rear door molding (P) | Rear door only lowered | Gap dimension | 0 mm | -1 mm | |
| Front door frame to B-pillar trim panel (R) | Gap dimension | 0.8 mm | +/-0.5 mm | ||
| Front door molding to rear door molding (P) | Rear door only lowered | Gap dimension | 0 mm | -1 mm | |
| Gap dimension from rear door frame to B-pillar trim panel (Q) | Gap dimension | 0.8 mm | +/-0.5 mm | ||
| Door window to molding and outer side section (F) | Gap dimension | 5 mm | |||
| Door to outer side section (G) | Door only raised (max. 1 mm) | Gap dimension | 4 mm | +/-0.7 mm | -0.5 mm |
| Door cover to outer door panel (H) | Gap dimension | 4 mm | |||
| Door cover to outer door panel (J) | Gap dimension | 0.5 mm | |||
| Front door to rear door (K) | Rear door only lowered (max. 1 mm) | Gap dimension | 4.5 mm | +/-0.7 mm | -0.5 mm |
| Outer roof panel to outer side section (E) | The projection of the side section at the outer roof panel is approx. 2.5 mm at the A-pillar, increases continuously to 3.5 mm to the C-pillar and then returns to 2.5 mm at the D-pillar. | Gap dimension | approx. 2.5 to 3.5 mm | ||
| Rear spoiler to outer roof panel (F) | Gap dimension | 6 mm | +/-1 mm | ||
| Rear spoiler to outer roof panel (G) | Only lowered | Gap dimension | 1 mm | ||
| Sunroof to outer roof panel (D) | Sliding-roof panel only lowered at front | Gap dimension | 0 mm | -1 mm | |
| Cover for sliding roof to outer roof panel, rear (Y) | Rear lid only raised | Gap dimension | 0 mm | +1 mm | |
| Lid 3 for panorama roof to lid 4 for panorama roof | Dimension -Y-, lid only raised | Adjustment value | 1 mm | +/-0.5 mm | |
| Lid 3 for panorama roof to lid 4 for panorama roof | Dimension -Z-, parallel gap | Adjustment value | approx. 7.1 mm | ||
| Lid 2 for panorama roof to lid 3 for panorama roof | Dimension -X-, lid only lowered | Adjustment value | 1 mm | +/-0.5 mm | |
| Lid 2 for panorama roof to lid 3 for panorama roof | Dimension -Z-, parallel gap | Adjustment value | approx. 7.1 mm | ||
| Lid 1 for panorama roof to lid 2 for panorama roof | Dimension -X-, lid only lowered | Adjustment value | 1 mm | +/-0.5 mm | |
| Lid 1 for panorama roof to lid 2 for panorama roof | Dimension -Z-, parallel gap | Adjustment value | approx. 7.1 mm | ||
| Lid 1 for panorama roof to outer roof panel | Dimension -X-, lid to outer roof panel raised | Adjustment value | 0.5 mm | +/-0.5 mm | |
| Rear lid to rear light (A) | Gap dimension | 4.5 mm | +/-0.8 mm | ||
| Rear light to outer side section (J) | Gap dimension | 3 mm | +/-0.5 mm | ||
| Rear light to rear apron (L) | Gap dimension | 3 mm | +/-1 mm | ||
| Rear lid trim to outer side section (B) | Gap dimension | 4.5 mm | +/-1 mm | ||
| Rear window to outer side section (C) | Gap dimension | 4.5 mm | +/-0.5 mm | ||
| Rear window to outer side section (D) | Gap dimension | 3.3 mm | +/-0.5 mm | ||
| Tank cap to outer side section (H) | All the way round | Gap dimension | 2 mm | +/-0.3 mm | |
| Rear light to outer side section (J) | Gap dimension | 3 mm | +/-0.5 mm | ||
| Rear apron to outer side section (K) | Gap is evident | Gap dimension | 0.5 mm | +/-0.5 mm | |
| Outer roof panel to outer side section (E) | The projection of the side section at the outer roof panel is approx. 2.5 mm at the A-pillar, increases continuously to 3.5 mm to the C-pillar and then returns to 2.5 mm at the D-pillar. | Gap dimension | approx. 2.5 to 3.5 mm | ||
| Door to outer side section (G) | Door only raised (max. 1 mm) | Gap dimension | 4 mm | +0.7 mm | -0.5 mm |
| Rear spoiler to outer side section (H) | Gap dimension | 5 mm | +/-1 mm | ||
| Rear spoiler to outer side section (I) | Gap dimension | 1 mm | |||
| Tank cap to outer side section (H) | All the way round | Gap dimension | 2 mm | +/-0.3 mm | |
| Rear window to outer side section (C) | Gap dimension | 4.5 mm | +/-0.5 mm | ||
| Rear window to outer side section (D) | Gap dimension | 3.3 mm | +/-0.5 mm | ||
| Molding to rear window (M) | Gap dimension | 4.7 mm | +/-0.8 mm | ||
| Rear lid trim panel to outer side section (B) | Gap dimension | 4.5 mm | +/-1 mm | ||
| Molding to rear window (M) | Gap dimension | 4.7 mm | +/-0.8 mm | ||
| Molding to rear lid trim panel (N) | Gap dimension | 2 mm | |||
| Trim panel to lid (O) | Gap dimension | 2 mm | +/-0.7 mm | ||
| Brake light to rear spoiler (E) | Gap dimension | 2 mm | |||
| Rear spoiler to outer roof panel (F) | Gap dimension | 6 mm | +/-0.5 mm | ||
| Rear spoiler to outer roof panel (G) | Only lowered | Gap dimension | 1 mm | ||
| Rear spoiler to outer side section (H) | Gap dimension | 5 mm | +/-1 mm | ||
| Rear spoiler to outer side section (I) | Gap dimension | 1 mm | |||
| Rear apron to outer side section (K) | Gap is evident | Gap dimension | 0.5 mm | +/-0.5 mm | |
| Rear light to rear apron (L) | Gap dimension | 3 mm | +/-1 mm | ||
| Bottom of rear lid to rear apron (P) | Gap dimension | 5.5 mm | +/-1 mm | ||
| Rear apron cover to rear apron (R) | Gap dimension | 1.5 mm | +/-0.7 mm | ||
| Rear apron cover to rear apron (S) | Gap dimension | 1.5 mm | +0.5 mm | -1 mm | |
| Rear apron cover to rear apron (T) | Gap dimension | 0.5 mm | +/-0.3 mm | ||
| Side of rear lid to rear apron (U) | Gap dimension | 4.5 mm | +/-0.5 mm | ||
| Rear lid to rear light (A) | Gap dimension | 4.5 mm | +/-0.8 mm | ||
| Rear lid trim panel to outer side section (B) | Gap dimension | 4.5 mm | +/-1 mm | ||
| Rear window to outer side section (C) | Gap dimension | 4.5 mm | +/-0.5 mm | ||
| Rear window to outer side section (D) | Gap dimension | 3.3 mm | +/-0.5 mm | ||
| Rear spoiler to outer roof panel (F) | Gap dimension | 6 mm | +/-1 mm | ||
| Rear spoiler to outer roof panel (G) | Only lowered | Gap dimension | 1 mm | ||
| Trim panel to rear lid (O) | Gap dimension | 2 mm | +/-0.7 mm | ||
| Bottom of rear lid to rear apron (P) | Gap dimension | 5.5 mm | +/-1 mm | ||
| Side of rear lid to rear apron (U) | Gap dimension | 4.5 mm | +/-0.5 mm |
Information
- Set gap dimensions on the lids, doors and covers, or accessories in accordance with the gap specifications.
- Given a clearance in the openings that is too great or too small, the movable body parts or the accessories must be centred accordingly.
- Ensure that the gaps do not run in a wedge-shaped fashion or do not narrow at local points.
- You can use star gauges for body gap dimensions NR.127-1 for this.
- The given values are guidelines which should be observed as far as possible.
- The guidelines apply to repair and assembly work.