Technical Values
WARNING: This page is about a different variant/trim than selected.
| Location | Description | Type | Basic value | Tolerance 1 | Tolerance 2 |
|---|---|---|---|---|---|
| Transmission/engine connection | Hexagon-head bolt no. 1 in figure, M12 x 70 | Tightening torque | 85 Nm (63 ftlb.) | ||
| Transmission/engine connection | Hexagon-head bolt no. 2 in figure M12 x 100; with washer | Tightening torque | 85 Nm (63 ftlb.) | ||
| Transmission-engine connection | Hexagon-head bolt No. 3 M12 x 90 in graphic | Tightening torque | 85 Nm (63 ftlb.) | ||
| Transmission/engine connection | Internal-serration screw no. 4 in figure M10 x 50 | Tightening torque | 45 Nm (33 ftlb.) | ||
| Transmission-engine connection | Nut No. 5 M10 in graphic | Tightening torque | 45 Nm (33 ftlb.) | ||
| Transmission-engine connection | Hexagon-head bolt No. 6 M12 x 70 in graphic | Tightening torque | 85 Nm (63 ftlb.) | ||
| Transmission-engine connection | Hexagon-head bolt No. 7 M12 x 90 in graphic | Tightening torque | 85 Nm (63 ftlb.) | ||
| Transmission support | Fastening screws between transmission support and transmission | Tightening torque | 65 Nm (48 ftlb.) | ||
| Hydraulic mount | Fastening screws between hydraulic mount and body | Tightening torque | 33 Nm (24 ftlb.) | ||
| Transmission support | Fastening screws between transmission support and transmission | Tightening torque | 65 Nm (48 ftlb.) | ||
| Hydraulic mount | Fastening screws between hydraulic mount and body | Tightening torque | 33 Nm (24 ftlb.) | ||
| Fastening screw | Fastening screws between coolant line and ATF cooler | Tightening torque | 23 Nm (17 ftlb.) | ||
| Fastening screw | Fastening screws between coolant line and ATF cooler | Tightening torque | 23 Nm (17 ftlb.) | ||
| Exhaust system mount | Fastening screws between transmission housing mount | Tightening torque | 45 Nm (33 ftlb.) | ||
| Retaining screw | Retaining screws between coolant pipe and transmission | Tightening torque | 23 Nm (17 ftlb.) | ||
| Drive shafts | Fastening screws between drive shaft and transmission flange | Tightening torque | 81 Nm (60 ftlb.) | ||
| Cross member | Fastening screws between cross member and body | Tightening torque | 65 Nm (48 ftlb.) | ||
| Anti-roll bar | Fastening screws between anti-roll bar and rear axle carrier side member | Tightening torque | 23 Nm (17 ftlb.) | ||
| Fastening screw | Fastening screws between coolant lines and ATF cooler | Tightening torque | 23 Nm (17 ftlb.) | ||
| Fastening screw | Fastening screws between coolant lines and ATF cooler | Tightening torque | 23 Nm (17 ftlb.) | ||
| Exhaust system mount | Fastening screws between transmission housing holder | Tightening torque | 45 Nm (33 ftlb.) | ||
| Retaining screw | Retaining screws between coolant pipe and transmission | Tightening torque | 23 Nm (17 ftlb.) | ||
| Drive shafts | Fastening screws between drive shaft and transmission flange | Tightening torque | 81 Nm (60 ftlb.) | ||
| Cross member | Fastening screws between cross member and body | Tightening torque | 65 Nm (48 ftlb.) | ||
| Anti-roll bar | Fastening screws between anti-roll bar and rear axle carrier side member | Tightening torque | 23 Nm (17 ftlb.) | ||
| Line holder | Fastening screws between line holder and engine transport eyebolt | Tightening torque | 10 Nm (7.5 ftlb.) | ||
| Line holder | Fastening screws between line holder and engine transport eyebolt | Tightening torque | 7.4 ftlb. | ||
| Converter screw connection | Fastening screws between torque converter and driver plate | Tightening torque | 28.8 ftlb. | ||
| Converter screw connection | Fastening screws between torque converter and driver plate | Tightening torque | 28.8 ftlb. | ||
| Converter screw connection | Fastening screws between torque converter and driver plate | Tightening torque | 28.8 ftlb. | ||
| Restraining cable | Fastening nut between restraining cable and cross member | Tightening torque | 23 Nm (17 ftlb.) |