Coding Tiptronic Control Unit
The procedure described must be applied when a control unit has to be replaced and the tester function Control unit replacement cannot be used.
Information
- When the transmission is renewed/replaced, the adaptation values must be reset using the PIWIS tester 9718 . It is expected that this function will not be implemented until tester software V8.0 is available:
- Resetting adaptation values:
- In the Tiptronic control module, select menu item Reset adaptation values and continue with [>>].
- Confirm with [F7] for Yes, [F8] for No and continue with [>>].
- Follow the instructions on the Tester.
- If a new control unit is installed, it must adapt first. Poor shifting quality can therefore be expected in the adaptation phase.
- After the test drive, let the engine run for 10 minutes at idle speed. This ensures that all adaptation values are stored in the control unit.
- The instructions of the Porsche System Tester have highest priority.
- The procedure listed has been structured generally; changes or additions may occur.
- Risk of irreparable damage to control unit
- Risk of damage to control unit
- Fault entries in the control unit
- Coding in the control unit is aborted
- Malfunctions in control unit, even during programming
→ Prior to disconnecting the control unit, switch off ignition and remove ignition key.
→ Ensure that the power supply is not interrupted during programming.
→ Connect a battery charger with a current rating of at least → Nominal value: 40 A to the vehicle battery.
- Risk of irreparable damage to control unit
- Risk of damage to control unit
- Fault entries in the control unit
- Coding in the control unit is aborted
- Malfunctions in control unit, even during programming
→ Prior to disconnecting the control unit, switch off ignition and remove ignition key.
→ Ensure that the power supply is not interrupted during programming.
→ Connect a battery charger with a current rating of at least → Nominal value: 40 A to the vehicle battery.
- Risk of irreparable damage to control unit
- Risk of damage to control unit
- Fault entries in the control unit
- Coding in the control unit is aborted
- Malfunctions in control unit, even during programming
→ Prior to disconnecting the control unit, switch off ignition and remove ignition key.
→ Ensure that the power supply is not interrupted during programming.
→ Connect a battery charger with a current rating of at least → Nominal value: 40 A to the vehicle battery.
- Risk of irreparable damage to control unit
- Risk of damage to control unit
- Fault entries in the control unit
- Coding in the control unit is aborted
- Malfunctions in control unit, even during programming
→ Prior to disconnecting the control unit, switch off ignition and remove ignition key.
→ Ensure that the power supply is not interrupted during programming.
→ Connect a battery charger with a current rating of at least → Nominal value: 40 A to the vehicle battery.
- PIWIS Tester 9718 must be connected to the vehicle before starting it. Switch on the ignition. Press [>>] to continue.
- Select the vehicle type .
- Switch to the Special functions menu and perform the vehicle handover using the [F8] key.
- In the Special functions menu, erase All fault memories by pressing [>>].
- Carry out automatic search of control units.
- Select Tiptronic with the cursor keys and press the [>>] key.
- Select Coding with the cursor keys and press the [>>] key.
- Select Vehicle version and code with the [F8] key.
South East Asia Japan Row/USA - Tester confirms: "Coding has been changed".
- If the control unit has been installed in another vehicle it will be necessary, as of Tester software 8.0, to Reset adaption values
:
- 10.1. In the menu Tiptronic , select the menu Reset adaption values and continue with [>>].
- 10.2. Confirm with [F7] for Yes, [F8] for No and continue with [>>].
- 10.3. Follow the instructions on the Tester.
- Quit the menu, perform test drive and check fault memory with the System Tester.