| Location |
Explanation |
Type |
Basic value |
Tolerance 1 |
Tolerance 2 |
| Brake caliper to wheel carrier front |
Thread M16 x 1.5 (Replace screws and lock nuts after each removal.) |
Tightening torque |
200 ftlb. |
|
|
| Brake caliper to wheel carrier rear |
Thread M14 x 1.5 (Replace screws and lock nuts after each removal.) |
Tightening torque |
133 ftlb. |
|
|
| Fastening screw, brake caliper to wheel hub (front and rear axle) |
Thread M12 x 1.5 (Replace screws and lock nuts after each removal.) |
Tightening torque |
10.5 ftlb. |
|
|
| Plug, brake disc rear |
Thread M12 x 1.5 x 5.5 |
Tightening torque |
10.5 ftlb. |
|
|
| Brake cover plate to front axle |
Thread M8 x 12 |
Tightening torque |
15 ftlb. |
|
|
| Caliper carrier to wheel carrier rear |
Thread M8 x 16 |
Tightening torque |
15 ftlb. |
|
|
| Caliper carrier to wheel carrier rear |
Thread M6 x 12 |
Tightening torque |
6 ftlb. |
|
|
| Retaining pin for front brake pads |
Thread M8 x 15 (always replace retaining pin) |
Tightening torque |
22 ftlb. |
+/-1.5 ftlb. |
|
| Speed sensor to front and rear axles |
Thread M6 x 16 |
Tightening torque |
6 ftlb. |
|
|
| Brake hose holder to wheel carrier front axle |
Thread M6 x 12 |
Tightening torque |
6.5 ftlb. |
|
|
| Cable holder to wheel carrier front axle |
Thread M8 x 14 |
Tightening torque |
22 ftlb. |
|
|
| Brake booster |
Thread M8 |
Tightening torque |
19 ftlb. |
+/-2 ftlb. |
|
| Mount for hydraulic unit support |
Thread M6 x 10 |
Tightening torque |
7.5 ftlb. |
|
|
| Mount for intermediate piece |
Thread M6 x 14 |
Tightening torque |
7.5 ftlb. |
|
|
| Foot-operated parking brake pedal to mounting bracket |
Thread M8 x 40 |
Tightening torque |
17 ftlb. |
|
|
| Foot-operated parking brake pedal to mounting bracket |
Thread M8 x 16 |
Tightening torque |
17 ftlb. |
|
|
| Deflector to body (tunnel) |
Thread M8 x 20 |
Tightening torque |
17 ftlb. |
|
|
| Pedals (pedal bearing block) to firewall |
Thread M8 x 20 |
Tightening torque |
17 ftlb. |
+/-2 ftlb. |
|
| Clutch slave cylinder to pedal bearing block |
Thread M6 x 25 |
Tightening torque |
7.5 ftlb. |
+/-1.0 ftlb. |
|
| Screws for articulated strut to pedal bearing block |
|
Tightening torque |
7.5 ftlb. |
+/-1.0 ftlb. |
|
| Brake lever shaft bolt (inserted from right to left) |
Thread M8 |
Tightening torque |
15 ftlb. |
+/-2 ftlb. |
|
| Clip (holder) stop light switch |
|
Tightening torque |
6 ftlb. |
+/-0.5 ftlb. |
|
| Wheel to wheel hub |
Thread M14 x 1.5 |
Tightening torque |
118 ftlb. |
|
|
| ABS cable holder to wheel carrier rear axle |
Thread M6 x 16 |
Tightening torque |
6 ftlb. |
|
|
| Brake line holder to brake caliper rear axle |
Thread M6 x 12 |
Tightening torque |
6 ftlb. |
|
|
| Cable holder for speed sensor/ABS to control arm rear (upper front) |
Thread M6 |
Tightening torque |
6 ftlb. |
|
|