Removing And Installing The Instrument Panel Bracket
WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2004 Porsche Boxster, 2003 Porsche Boxster, 2002 Porsche Boxster, 2001 Porsche Boxster, and 2000 Porsche Boxster. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:
- Before removing the instrument panel bracket, the instrument panel must be disassembled. SeeREMOVING AND INSTALLING THE INSTRUMENT PANEL BRACKET .
REMOVAL AND INSTALLATION PROCEDURE FOR INSTRUMENT PANEL BRACKET
| No. | Designation | Qty. | Removal | Installation | ||
|---|---|---|---|---|---|---|
| 2(1) | Fastening screws | 4 | ||||
| 7(1) | Sheetmetal nut | 4 | ||||
| 8(1) | Fastening screws | 4 | See TIGHTENING TORQUE . | |||
| 9(1) | Threaded plate | 4 | Is screwed into position with the compensating element -10-8- (1) | |||
| 10(1) | Compensating element | 4 | The compensating element -10-8- (1) | By screwing in the fastening screws -8-10- (1) | ||
| 11(1) | Fastening screws | 2 | See TIGHTENING TORQUE . | |||
| 12(1) | Instrument panel bracket | 1 | Undo the fastening screws -8-10-12- (1) | Insert instrument panel bracket -12-10-8 and 11- (1) | ||
| 13A(1) | Closure cap | 2 | Pull out. | Press in. | ||
| 13B(1) | Plug | 2 | Only installed on 911 coup"EACUTE"A versions. | |||
| 14(1) | Sheetmetal clip | 4 | Check, replace if necessary. | |||
| 15(1) | Fastening screws | 4 | See TIGHTENING TORQUE . | |||
| 16A(1) | USA version, knee protector strip | 1 | Unscrew fastening screws -15-16A- (1) | Secure the knee protector strip -16A-12-15- (1) | ||
| 16B(1) | USA version, knee protector strip | 1 | Unscrew fastening screws -15-16B- (1) | Secure the knee protector strip -16B-12-15- (1) | ||
| 17(1) | Cowl panel seal | 1 | is destroyed when removed. | Tighten protective film. | ||
| 18(1) | Adhesive pad | 1 | Is destroyed when removed. |
The bonding area must be free of dust and grease. Tighten protective film and position it. |
||
| 19(1) | Clip | 4 | ||||
| 20(1) | Fastening screws | 4 | See TIGHTENING TORQUE . | |||
| 21(1) | Shear-off nut | 2 | Undo the shear-off nut with special tool 9259. | |||
| 23(1) | Airbag control module | 1 | Refer to REMOVING AND INSTALLING TRIGGERING UNIT FOR AIRBAG . | Refer to REMOVING AND INSTALLING TRIGGERING UNIT FOR AIRBAG . | ||
| 24(1) | Cover panel | 4 | Fix the cover panel in the body and the instrument panel bracket -12-20- (1) | |||
| 25(1) | Fastening screws | 2 | See TIGHTENING TORQUE . | |||
| 26(1) | Cover panel | 1 | Unscrew fastening screws -25- (1) | |||
| 27(1) | Strut | 1 | Unscrew fastening screws -2-27- (1) | Position strut -27-12-2- (1) | ||
|
||||||