Input signals

The following queries can be run using this menu item:

GAL (noise-dependent loudspeaker boost - NLB)
Increment steps
Key code
Tuner parameters
Status of the optical performance check

NOTE: Deactivate the automatic traffic announcement before performing the diagnosis on the CDR23. If this is not done, the system will crash.

INPUT SIGNALS - CDR23

Menu item	Function
GAL (noise-dependent loudspeaker boost - NLB)	You can read out the coded NLB value using this menu item. Connect and start the Porsche System Tester II 9588 and switch on the ignition. Select 911 (996) in the Vehicle type menu and confirm with the "FORWORD" key. Select PCM in the Control modules menu and confirm with the "FORWORD" key. Select CDR23 in the 911 (996) PCM2 function selection menu and confirm with the "FORWORD" key. Select Input signals in the 911 (996) CDR23 function selection menu and confirm with the "FORWORD" key. Select GAL (noise-dependent loudspeaker boost - NLB) in the 911 (996) CDR23 function selection menu and confirm with the "FORWORD" key. The current coded value is displayed in the 911 (996) CDR23 noise-dependent loudspeaker menu.
Increment steps	You can check the function of the CDR23 rotary knobs using this menu item. Connect and start the Porsche System Tester II 9588 and switch on the ignition. Select 911 (996) in the Vehicle type menu and confirm with the "FORWORD" key. Select PCM in the Control modules menu and confirm with the "FORWORD" key. Select CDR23 in the 911 (996) PCM2 function selection menu and confirm with the "FORWORD" key. Select Input signals in the CDR23 function selection menu and confirm with the "FORWORD" key. Select Increment steps in the 911 (996) CDR23 Input signals menu and confirm with the "FORWORD" key. The relevant change is displayed by turning the rotary knobs of the CDR23 if this functions correctly.
Key code	You can check the function of the CDR23 operating buttons using this menu item. Connect and start the Porsche System Tester II 9588 and switch on the ignition. Select 911 (996) in the Vehicle type menu and confirm with the "FORWORD" key. Select PCM in the Control modules menu and confirm with the "FORWORD" key. Select CDR23 in the 911 (996) PCM2 function selection and confirm with the "FORWORD" key. Select Input signals in the CDR23 function selection and confirm with the "FORWORD" key. Select Key code in the 911 (996) CDR23 function selection and confirm with the "FORWORD" key. By operating the buttons of the CDR23, the correct function of each key code is displayed.
Tuner parameters	You can check the tuner parameters of the CDR23 using this menu item. Connect and start the Porsche System Tester II 9588 and switch on the ignition. Select 911 (996) in the Vehicle type menu and confirm with the "FORWORD" key. Select PCM in the Control modules menu and confirm with the "FORWORD" key. Select CDR23 in the 911 (996) PCM function selection and confirm with the "FORWORD" key. Select Input signals in the CDR23 function selection and confirm with the "FORWORD" key. Select Tuner parameters in the 911 (996) CDR23 Input signals function selection and confirm with the "FORWORD" key. The currently coded country code is displayed in the CDR23 Tuner parameters menu.
Status of the optical performance check	You can check the status of the optical waveguides using this menu item. Connect and start the Porsche System Tester II 9588 and switch on the ignition. Select 911 (996) in the Vehicle type menu and confirm with the "FORWORD" key. Select PCM in the Control modules menu and confirm with the "FORWORD" key. Select CDR23 in the 911 (996) PCM2 function selection and confirm with the "FORWORD" key. Select Input signals in the CDR23 function selection and confirm with the "FORWORD" key. Select Key code in the 911 (996) CDR23 input signals function selection and confirm with the "FORWORD" key. Select Status of optical performance check in the CDR23 input signals menu and confirm with the "FORWORD" key. The result can be read out.