LEMON Manuals: Even more car manuals for everyone
Home >> Pontiac >> 2009 >> Vibe Base, 2.4 0, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 120 (Engine Mechanical - 4.6L - Repair Instructions - On Vehicle) >> Repair Instructions - On Vehicle >> Camshaft Replacement - Right Side >> Removal Procedure

Removal Procedure

WARNING: This page is about a different car, the 2011 Cadillac DTS. However, it is still accessible from the selected car via links, so may be relevant.
  1. Remove the right camshaft cover. Refer to Camshaft Cover Replacement - Right Side .
  2. Remove the camshaft position sensor. Refer to Camshaft Position Sensor Replacement .
    3. Fig 1: Ensuring Camshaft Sprocket Drive Pins Are At Top Of Their Rotation
    GM517164Courtesy of GENERAL MOTORS COMPANY
  3. Rotate the crankshaft to TDC of the # 1 cylinders compression stroke, both camshaft sprocket drive pins should be at the top of their rotation.
    4. Fig 2: Using Camshaft Holding Tool
    GM650538Courtesy of GENERAL MOTORS COMPANY
    WARNING:

    Refer to Camshaft Holding Tool Warning .

  4. Install the J 44212 over the camshafts.
    5. Fig 3: Painting A Mark On The Timing Chain Link Adjacent To Each Camshaft Sprocket Timing Mark
    GM1275692Courtesy of GENERAL MOTORS COMPANY
  5. Use a paint stick to create a mark (1) on the timing chain link adjacent to each camshaft sprocket timing mark (2, 3).
    6. Fig 4: Identifying Timing Chain Retention Tool Components
    GM1275725Courtesy of GENERAL MOTORS COMPANY
  6. Install both EN 46327 (1) to the engine using the following step:

    Rotate the wing nut (2) of the EN 46327 (3) to the top of its travel.

    7. Fig 5: Bottom Retention Tool On The Cylinder Head
    GM1275702Courtesy of GENERAL MOTORS COMPANY
  7. Position the bottom retention tool on the cylinder head with the V-notch of the block (1) adjacent to the right exhaust camshaft sprocket and chain.
    8. Fig 6: Hook End In Secondary Timing Chain Link
    GM1275713Courtesy of GENERAL MOTORS COMPANY
  8. Insert the hook end (2) into a secondary timing chain link as shown.
    9. Fig 7: Bottom Retention Tool On The Cylinder Head
    GM1275702Courtesy of GENERAL MOTORS COMPANY
  9. Rotate the wing nut until it contacts the retention tool block (1). DO NOT tighten the wing nut at this time.
    10. Fig 8: Identifying Timing Chain Retention Tool Components
    GM1275725Courtesy of GENERAL MOTORS COMPANY
  10. Rotate the wing nut (2) of the EN 46327 (4) to the top of its travel.
    11. Fig 9: Positioning Top Retention Tool On Cylinder Head
    GM1275703Courtesy of GENERAL MOTORS COMPANY
  11. Position the top retention tool on the cylinder head with the V-notch of the block (1) adjacent to the right intake camshaft sprocket and chain.
    12. Fig 10: View Of Hook End In Secondary Timing Chain Link
    GM1275718Courtesy of GENERAL MOTORS COMPANY
  12. Insert the hook end (2) into a secondary timing chain link as shown.
    13. Fig 11: Positioning Top Retention Tool On Cylinder Head
    GM1275703Courtesy of GENERAL MOTORS COMPANY
  13. Rotate the wing nut until it contacts the retention tool block (1). Alternately tighten both wing nuts to retain the chain.
    14. Fig 12: Securing Camshaft Using An Open End Wrench
    GM749353Courtesy of GENERAL MOTORS COMPANY
    CAUTION:

    Refer to Torque Reaction Against Timing Drive Chain Caution .

  14. Use an open wrench on the hex cast into the camshafts in order to prevent the camshafts from rotating when removing the camshaft sprocket bolts.
    15. Fig 13: Identifying Right Exhaust Camshaft Sprocket Bolt
    GM650548Courtesy of GENERAL MOTORS COMPANY
  15. Remove the camshaft sprocket bolts.
  16. Remove the camshaft sprockets.
    17. Fig 14: View of Camshaft Bearing Cap
    GM591917Courtesy of GENERAL MOTORS COMPANY
  17. Alternately loosen the camshaft bearing cap bolts a few turns at a time until all valve spring pressure has been released.
  18. Remove the camshaft bearing caps.
  19. Remove the J 44212 from the camshafts.
    20. Fig 15: View of Camshafts
    GM591915Courtesy of GENERAL MOTORS COMPANY
  20. Remove the camshafts.
    21. Fig 16: View of Camshaft Followers
    GM609694Courtesy of GENERAL MOTORS COMPANY
  21. Remove the camshaft followers.
  22. Clean and inspect the camshafts. Refer to Camshaft Cleaning and Inspection .
scientia non olet · About LEMON Manuals