LEMON Manuals: Even more car manuals for everyone
Home >> Pontiac >> 2008 >> Torrent GXP, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 88 (Automatic Transmission - AF33-5 - Removal & Installation, Service, Overhaul, Troubleshooting & Diagnosis) >> Manual Shift Detent Lever and Park Pawl Installation

Manual Shift Detent Lever and Park Pawl Installation

WARNING: This page is about a different car, the 2009 Pontiac Torrent and 2009 Chevrolet Equinox. However, it is still accessible from the selected car via links, so may be relevant.
    Fig 1: View Of Park Pawl Pin Spring, Guide Sleeve & Bolt/Screw
    GM749462Courtesy of GENERAL MOTORS CORP.
  1. Install the park pawl pin spring (704).
  2. Install the park pawl pin spring guide sleeve (705).
    3. CAUTION: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  3. Install the park pawl bolt/screw (706). Tighten the park pawl bolt to 10 N.m (89 lb in).
    4. Fig 2: View Of Park Pawl Spring Pin
    GM749461Courtesy of GENERAL MOTORS CORP.
  4. Install the park pawl spring pin (703).
    5. Fig 3: View Of Park Pawl & Actuator Bracket
    GM798649Courtesy of GENERAL MOTORS CORP.
  5. Install the park pawl (702) and the park pawl actuator bracket (708).
    6. Fig 4: View Of Park Pawl Shaft & Return Spring
    GM798650Courtesy of GENERAL MOTORS CORP.
  6. Install the park pawl return spring (701).
  7. Install the park pawl shaft (700).
    8. Fig 5: View Of Manual Shift Detent Spring Assembly
    GM749456Courtesy of GENERAL MOTORS CORP.
  8. Install the manual shift detent spring assembly (711).
    9. Fig 6: View Of Manual Shift Detent Lever Spring Bolt/Screw & Park Pawl Actuator Bracket Bolt/Screw
    GM749455Courtesy of GENERAL MOTORS CORP.
  9. Install and hand tighten the 14 mm manual shift detent lever spring bolt (712) and the 16.7 mm park pawl actuator bracket bolt (715).
    • Tighten the 14 mm manual shift detent lever spring bolt (712) to 5 N.m (44 lb in) .
    • Tighten the 16.7 mm park pawl actuator bracket bolt (715) to 10 N.m (89 lb in) .
    10. Fig 7: View Of Park Pawl Actuator Rod
    GM749454Courtesy of GENERAL MOTORS CORP.
  10. Install the park pawl actuator rod (709).
    11. Fig 8: View Of Manual Shift Detent Lever Assembly
    GM749453Courtesy of GENERAL MOTORS CORP.
  11. Install the manual shift detent lever assembly (710).
    12. NOTE: The park pawl actuator rod (709) must be installed with the rod between the case and the manual shift detent lever.
  12. Connect the park pawl actuator rod (709) to the manual shift detent lever assembly (710).
    13. Fig 9: Lifting Manual Shift Detent Lever Spring
    GM874467Courtesy of GENERAL MOTORS CORP.
  13. Using a screwdriver, lift the manual shift detent lever spring (711) and rotate the manual shift detent lever assembly (710) into position.
scientia non olet · About LEMON Manuals