Conditions for Running the DTC

WARNING: This page is about a different variant/trim than selected.

P0133

DTCs P0030, P0053, P0068, P0101, P0102, P0103, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0128, P0131, P0132, P0134, P0135, P0201, P0202, P0203, P0204, P0205, P0206, P0220, P0300, P0442, P0443, P0446, P0449, P0451, P0452, P0454, P0455, P0496, P1516, P2101, P2119, P2135 are not set.
The system voltage is between 10-18 volts.
The scan tool special functions are not active.
The HO2S Sensor 1 Heater command parameter is ON.
The ECT sensor parameter is more than 65°C (149°F).
The Engine Run Time parameter is more than 60 seconds.
The vehicle is not in Park, Reverse, or Neutral.
The Loop Status parameter is closed.
The MAF sensor parameter is between 15-29 g/s.
The TP Indicated Angle parameter is more than 2 percent.
The Engine Speed parameter is between 1,300-2,200 RPM.
The evaporative emission (EVAP) system is purging.
The Barometric (BARO) parameter is at least 69.8 kPa.
The above conditions have been met for one second.

P0134

DTCs P0030, P0053, P0068, P0101, P0102, P0103, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0128, P0201, P0202, P0203, P0204, P0205, P0206, P0220, P0442, P0443, P0446, P0449, P0451, P0452, P0453, P0454, P0455, P0496, P1516, P2101, P2119, P2135 are not set.
The system voltage is between 10-18 volts.
The scan tool special functions are not active.
The HO2S Sensor 1 Heater command parameter is ON.
The Engine Run Time parameter is more than 120 seconds.

P0140 - Regular Test

DTCs P0036, P0054, P0068, P0101, P0102, P0103, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0128, P0201, P0202, P0203, P0204, P0205, P0206, P0220, P0442, P0443, P0446, P0449, P0451, P0452, P0453, P0454, P0455, P0496, P1516, P2101, P2119, P2135 are not set.
The system voltage is between 10-18 volts.
The scan tool special functions are not active.
The Engine Run Time parameter is more than 2 minutes.
The TP Indicated Angle parameter has changed more than 8 percent at least 3 times.
The Loop Status parameter is closed.

P0140 - Fast Pass Test

DTCs P0036, P0054, P0068, P0101, P0102, P0103, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0128, P0201, P0202, P0203, P0204, P0205, P0206, P0220, P0442, P0443, P0446, P0449, P0451, P0452, P0453, P0454, P0455, P0496, P1516, P2101, P2119, P2135 are not set.
The system voltage is between 10-18 volts.
The scan tool special functions are not active.
This vehicle uses the following 2 methods to enable and run this diagnostic:
- The Engine Run Time parameter is less than 90 seconds.
  OR
- A cold start condition has been detected, identified by the following conditions:
  - The Start-Up ECT parameter is less than 35°C (95°F).
  - The Start-Up intake air temperature (IAT) parameter is less than 35°C (95°F).
  - The difference between the Start-Up ECT parameter and the Start-Up IAT parameter is less than 6°C (10.8°F).

P1133 and P1134

DTCs P0030, P0053, P0068, P0101, P0102, P0103, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0128, P0131, P0132, P0134, P0135, P0201, P0202, P0203, P0204, P0205, P0206, P0220, P0300, P0442, P0443, P0446, P0449, P0451, P0452, P0454, P0455, P0496, P1516, P2101, P2119, P2135, P2A00 are not set.
The system voltage is between 10-18 volts.
The scan tool special functions are not active.
The HO2S Sensor 1 Heater command parameter is ON.
The current misfire condition is not detected.
The ECT Sensor parameter is more than 65°C (149°F).
The Engine Run Time parameter is at least 60 seconds.
The EVAP purge solenoid is commanded ON.
The MAF sensor parameter is between 15-30 g/s.
The Engine Speed parameter is between 1,300-3,000 RPM.
The TP Indicated Angle parameter is greater than 2 percent.
The Loop Status parameter is closed.
The BARO parameter is at least 69.8 kPa.
The vehicle is not in Park, Reverse, or Neutral.

P2A00

DTCs P0030, P0053, P0068, P0101, P0102, P0103, P0107, P0108, P0112, P0113, P0117, P0118, P0120, P0128, P0131, P0132, P0133, P0134, P0135, P0201, P0202, P0203, P0204, P0205, P0206, P0220, P0442, P0443, P0446, P0449, P0451, P0452, P0453, P0454, P0455, P0496, P1133, P1516, P2101, P2119, P2120, P2122, P2123, P2135 are not set.
DTCs P0411, P0412, P0418, P2430, P2431, P2432, P2433, P2440, P2444 are not set, where applicable.
The Engine Run Time parameter is at least 3 minutes.
The traction control, if equipped, is not active.
The control module is not commanding power enrichment (PE) or Decel Fuel Cutoff modes.
The MAF Sensor parameter is between 8-38 g/s.
The Engine Speed parameter is between 602-3,000 RPM.
The TP Indicated Angle parameter is between 3-35 percent.
The ECT Sensor parameter is more than 65°C (149°F).
The system voltage is between 10-18 volts.
The exhaust gas recirculation (EGR) flow diagnostic is not active.
The above conditions have been met for 3 seconds.

P2A01 - Passive Test

DTCs P0030, P0053, P0068, P0101, P0102, P0103, P0107, P0108, P0112, P0113, P0117, P0118, P0120, P0123, P0128, P0131, P0132, P0133, P0134, P0135, P0201, P0202, P0203, P0204, P0205, P0206, P0220, P0442, P0443, P0446, P0449, P0451, P0452, P0453, P0454, P0455, P0496, P1133, P1516, P2101, P2119, P2135 are not set.
DTCs P0411, P0412, P0418, P2430, P2431, P2432, P2433, P2440, P2444 are not set, where applicable.
The engine is running for at least 6 seconds.
The ignition voltage is between 10-18 volts.

P2A01 - Intrusive Test

DTCs P0030, P0053, P0068, P0101, P0102, P0103, P0107, P0108, P0112, P0113, P0117, P0118, P0120, P0123, P0128, P0131, P0132, P0133, P0134, P0135, P0201, P0202, P0203, P0204, P0205, P0206, P0220, P0442, P0443, P0446, P0449, P0451, P0452, P0453, P0454, P0455, P0496, P1133, P1516, P2101, P2119, P2135 are not set.
DTCs P0411, P0412, P0418, P2430, P2431, P2432, P2433, P2440, P2444 are not set, where applicable.
The Engine Run Time parameter is more than 6 minutes.
The ignition voltage is between 10-18 volts.
The Engine Speed parameter is between 1,000-3,000 RPM.
The calculated MAF is between the following:
- For L26-13-40 g/s
The Vehicle Speed parameter is between 32-128 km/h (20-80 mph).
When all of the above conditions have been met for at least 2.5 seconds, the following conditions must also be met:
- The evaporative emission (EVAP) purge diagnostic is not active.
- The Short Term FT parameter is between +4 and -4 percent.
- The Loop Status parameter is closed.
- The EVAP purge solenoid is greater than 0 percent.