LEMON Manuals: Even more car manuals for everyone
Home >> Pontiac >> 2007 >> Grand Prix GXP >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 3 (Engine Controls & Fuel - 3.8L - Diagnosis & Troubleshooting) >> Electronic Ignition (EI) System Diagnosis >> Circuit Description

Circuit Description

WARNING: This page is about a different variant/trim than selected.

The ignition control module (ICM) has independent power and ground circuits. The circuits between the ICM and the powertrain control module (PCM) consists of the following circuits:

For a complete system description, refer to Electronic Ignition (EI) System Description .

Electronic Ignition (EI) System Diagnosis

Step Action Values Yes No
Schematic Reference: Engine Controls Schematics
Connector End View Reference: Engine Controls Connector End Views or Powertrain Control Module Connector End Views
1 Did you perform the Diagnostic System Check - Vehicle? - Go to Step 2  Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2 Attempt to start the engine.
Does the engine start and run?		 - Go to Step 5  Go to Step 3 
3
  1. Observe the Engine Speed parameter with a scan tool.
  2. Crank the engine.
Does the scan tool indicate RPM is present?		 - Go to Step 4  Go to Crankshaft Position Sensor System Diagnosis 
4
  1. Disconnect the ignition control module (ICM) connector.
  2. Jumper each of the following circuits at the connector to each respective mate at the ICM:
    • Pin P ignition 1 voltage
    • Pin K Ground
    • Pin H CKP sensor 2 signal
    • Pin N 12-volt reference
    • Pin M low reference

      Refer to Using Connector Test Adapters in Wiring Systems.

  3. Measure the frequency from the crankshaft position (CKP) sensor 2 signal circuit at the jumper wire terminal to a good ground with a DMM.
  4. Crank the engine.
Is the frequency more than the specified value?		 0 Hz Go to Step 5  Go to Crankshaft Position Sensor System Diagnosis 
5
  1. Remove the fuel pump relay with the J 43244  Relay Puller Pliers. See Special Tools .
    2. IMPORTANT: Ground the companion cylinder of the cylinder being tested.
  2. Test for spark at each cylinder with a J 26792  Spark Tester. See Special Tools .
Did you have spark on any of the cylinders?		 - Go to Step 6  Go to Step 14 
6 Did you have spark on all of the cylinders? - Go to Step 7  Go to Step 9 
7 Does the spark tester indicate a bright blue spark on all cylinders? - Go to Step 8  Go to Step 9 
8
  1. Remove the spark plugs.
  2. Examine the spark plugs for any abnormal conditions or damage. Refer to Spark Plug Inspection .
Are the spark plugs in good condition?		 - System OK Go to Step 15 
9
  1. Turn OFF the ignition.
  2. Connect the J 26792  to the spark plug wire of the inoperative cylinder. See Special Tools .
  3. Switch the inoperative spark plug wire connection with a known good cylinder at the ignition coils.
  4. Crank the engine.
Do you have spark on the inoperative cylinder?		 - Go to Step 12  Go to Step 10 
10
  1. Disconnect the spark plug wires from the inoperative ignition coil.
  2. Measure the secondary resistance of the ignition coil.
Is the resistance within the specified range?		 5,000-8,000 Ω Go to Step 11  Go to Step 17 
11
  1. Remove the inoperative ignition coil.
  2. Connect a test lamp between the control circuits of the ignition coil on the ICM.
  3. Crank the engine.
Does the test lamp turn ON and OFF while the engine is being cranked?		 - Go to Step 13  Go to Step 14 
12 Test the spark plug wires for the following:
Did you find and correct the condition?		 - Go to Step 19  Go to Step 16 
13 Test for an intermittent and for a poor connection at the ignition coil. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 19  Go to Step 17 
14 Test for an intermittent and for a poor connection at the ICM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 19  Go to Step 18 
15 Replace the spark plugs. Refer to Spark Plug Replacement .
Did you complete the replacement?		 - Go to Step 19  -
16 Replace the spark plug wires. Refer to Spark Plug Wire Replacement .
Did you complete the replacement?		 - Go to Step 19  -
17 Replace the ignition coil. Refer to Ignition Coil Replacement .
Did you complete the replacement?		 - Go to Step 19  -
18 Replace the ICM. Refer to Ignition Control Module Replacement .
Did you complete the replacement?		 - Go to Step 19  -
19
  1. Turn the ignition OFF for 30 seconds.
  2. Start the engine and operate the vehicle.
  3. Observe the vehicle performance and driveability.
Does the vehicle operate normally?		 - System OK Go to Step 1 
scientia non olet · About LEMON Manuals