LEMON Manuals: Even more car manuals for everyone
Home >> Pontiac >> 2006 >> Vibe Base, AWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 10 (Engine Control System - 1.8L (LNK) - DTC P0453 To DTC P2647) >> DTC P2440 >> Test Description

Test Description

WARNING: This page is about a different variant/trim than selected.

The numbers below refer to the step numbers on the diagnostic table.

  1. 1:  The Diagnostic System Check - Vehicle prompts the technician to complete some basic checks and store the Freeze Frame data on the scan tool, if applicable. This creates an electronic copy of the data taken when the fault occurred. The information is then stored in the scan tool for later reference.
  2. 3:  This step tests for criss-crossed vacuum hoses at the AIR solenoid valve. If the vacuum hoses are connected incorrectly, the vacuum will not bleed away when the AIR solenoid is turned OFF, leaving the AIR shut-off valve always OPEN.
  3. 4:  This step tests for an always ON AIR solenoid valve. After a maximum time of 30 seconds, the AIR solenoid is turned OFF.
  4. 5:  This step verifies the operation of the AIR solenoid valve. If there is still vacuum pressure after the AIR pump is OFF, the solenoid vent passage is blocked.
  5. 6:  This step tests for a shorted solenoid control circuit.
  6. 8:  This step tests for a stuck OPEN AIR shut-off valve.
DTC P2440

Step Action Yes No
Schematic Reference: Engine Controls Schematics
Connector End View Reference: Powertrain Control Module (PCM) Connector End Views or Engine Controls Connector End Views
1  Did you perform the Diagnostic System Check - Vehicle? Go to Step 2  Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2 Install a scan tool and check for DTCs.
Is DTC P2430, P2431, P2432, or P2433 present?		 Go to DTC P2430 , DTC P2431 , DTC P2432 , or DTC P2433  Go to Step 3 
3 
  1. Inspect for the correct routing of the vacuum hoses to the secondary air injection (AIR) solenoid valve:
    • The hose to the inboard port of the solenoid is connected to the AIR shut-off valve
    • The hose to the outboard port of the solenoid is connected to the manifold vacuum supply
  2. Repair as necessary. Refer to Emission Hose Routing Diagram .
Did you find and correct a condition?		 Go to Step 12  Go to Step 4 
4 
  1. Disconnect the vacuum hose at the secondary air injection (AIR) shut-off valve.
  2. Connect a vacuum gage to the vacuum hose.
  3. Start the engine and run the engine for at least 1 minute.
Is the vacuum gage still indicating pressure after running the engine for 1 minute?		 Go to Step 6  Go to Step 5 
5 
  1. Command the AIR solenoid valve and the AIR pump ON with the scan tool. Refer to Scan Tool Output Controls .
  2. Observe the vacuum gage when the pump is ON and after the pump turns OFF.
Did the vacuum gage indicate pressure even after the AIR pump turned OFF?		 Go to Step 9  Go to Step 8 
6 
  1. Turn OFF the ignition.
  2. Disconnect the electrical connector of the AIR solenoid valve.
  3. Start the engine.
Does the vacuum gage still indicate pressure with the engine running?		 Go to Step 9  Go to Step 7 
7
  1. Test for a short to ground in the control circuit of the AIR solenoid valve. Refer to Circuit Testing in Wiring Systems.
  2. Repair as necessary. Refer to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 12  Go to Step 11 
8 
  1. Turn OFF the ignition.
  2. Remove the AIR shut-off valve. Refer to Secondary Air Injection (AIR) Shut-Off Valve Replacement .
  3. Blow air into the large port on the AIR pump side of the AIR shut-off valve.
Does the air pass through the AIR shut-off valve?		 Go to Step 10  Go to Intermittent Conditions
9 Replace the AIR solenoid valve. Refer to Secondary Air Injection (AIR) Solenoid Valve Replacement .
Did you complete the replacement?		 Go to Step 12  -
10 Replace the AIR shut-off valve. Refer to Secondary Air Injection (AIR) Shut-Off Valve Replacement .
Did you complete the replacement?		 Go to Step 12  -
11 Replace the powertrain control module (PCM). Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.
Did you complete the replacement?		 Go to Step 12  -
12
  1. Use the scan tool in order to clear the DTCs.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC.
Did a DTC P2440 set?		 Go to Step 3  Go to Step 13 
13 With a scan tool, observe the stored information, Capture Info.
Does the scan tool display any DTCs that you have not diagnosed?		 Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information System OK
scientia non olet · About LEMON Manuals