LEMON Manuals: Even more car manuals for everyone
Home >> Pontiac >> 2006 >> Vibe Base, AWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 10 (Engine Control System - 1.8L (LNK) - DTC P0453 To DTC P2647) >> DTC P2432 >> Test Description

Test Description

WARNING: This page is about a different variant/trim than selected.

The numbers below refer to the step numbers on the diagnostic table.

  1. 1:  The Diagnostic System Check - Vehicle prompts the technician to complete some basic checks and store the Freeze Frame data on the scan tool, if applicable. This creates an electronic copy of the data taken when the fault occurred. The information is then stored in the scan tool for later reference.
  2. 2:  This step determines if DTC P2432 is the result of a hard failure or an intermittent condition. Normal pressure sensor input voltage is approximately 1.6 volts with the ignition ON, AIR pump OFF.
  3. 5:  This step checks for an open in the pressure sensor reference voltage circuit.
  4. 6:  The pressure sensor signal circuit carries a 5-volt bias that can be measured with the DMM. If the measured voltage is near zero there is a short to ground or a faulty PCM.
DTC P2432

Step Action Values Yes No
Schematic Reference:  Engine Controls Schematics 
Connector End View Reference:  Powertrain Control Module (PCM) Connector End Views  or  Engine Controls Connector End Views 
1  Did you perform the Diagnostic System Check - Vehicle? - Go to Step 2  Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2 
  1. Turn ON the ignition, with the engine OFF.
  2. Backprobe the input circuit of the secondary air injection (AIR) pressure sensor with a DMM to ground.
Is the pressure sensor input circuit voltage within the specified value?		 1.5-1.6 V Go to Step 3  Go to Step 4 
3
  1. Use the scan tool in order to clear the DTCs.
  2. Start the engine.
  3. Operate the vehicle within the Freeze Frame conditions as specified or within the Conditions for Running the DTC. Review the supporting text.
Did DTC P2432 set?		 - Go to Step 4  Go to Diagnostic Aids
4 Was DTC P0122 also set? - Go to Step 9  Go to Step 5 
5 
  1. Turn OFF the ignition.
  2. Disconnect the pressure sensor electrical connector.
  3. Turn ON the ignition, with the engine OFF.
  4. Measure the pressure sensor 5-volt reference circuit with a DMM.
Is the voltage near the specified value?		 5.0 V Go to Step 6  Go to Step 8 
6  Measure the voltage of the pressure sensor input circuit with a DMM.
Is the voltage near the specified value?		 4.9 V Go to Step 10  Go to Step 7 
7
  1. Test the pressure sensor input circuit for a short to ground.
  2. Repair as necessary. Refer to Wiring Repairs in Wiring Systems.
Was a repair necessary?		 - Go to Step 12  Go to Step 11 
8 Repair the open in the 5-volt reference sensor circuit between the pressure sensor and SP108. Refer to Wiring Repairs in Wiring Systems.
Is the action complete?		 - Go to Step 12  -
9 Repair the open in the 5-volt reference sensor circuit between the powertrain control module (PCM) and SP108. Refer to Wiring Repairs in Wiring Systems.
Is the action complete?		 - Go to Step 12  -
10 Replace the AIR pressure sensor. Refer to Secondary AIR Injection Pressure Sensor Replacement .
Is the action complete?		 - Go to Step 12  -
11 Replace the PCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.
Is the action complete?		 - Go to Step 12  -
12
  1. Use the scan tool in order to clear the DTCs.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC, as specified by the supporting text.
Does the DTC run and pass?		 - Go to Step 13  Go to Step 2 
13 With a scan tool, observe the stored information, Capture Info.
Does the scan tool display any DTCs that you have not diagnosed?		 - Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information System OK
scientia non olet · About LEMON Manuals