Activating System
- Disconnect negative battery cable. Wait at least one minute. This is the time required for back-up power supply in diagnostic monitor to deplete its stored energy. Remove air bag simulator(s).
- Install driver-side air bag module and passenger-side air bag module (if equipped). Tighten mounting bolts to specification. See TORQUE SPECIFICATIONS . Connect negative battery cable. Perform SYSTEM OPERATION CHECK .
- Disconnect negative battery cable. Wait at least one minute. Remove air bag simulators from driver-side and passenger-side air bag wiring harness connectors.
- Connect driver-side air bag connector to air bag module. Install driver-side air bag module onto steering wheel. See DRIVER-SIDE AIR BAG MODULE .
- Connect passenger-side air bag connector to air bag module. Install passenger-side air bag into instrument panel. See PASSENGER-SIDE AIR BAG MODULE . Connect negative battery cable. Perform SYSTEM OPERATION CHECK . Program radio station frequencies.
- Connect negative battery cable. Disconnect positive battery cable. Wait at least one minute. This is the time required for back-up power supply in diagnostic monitor to deplete its stored energy. Remove air bag simulators.
- Install driver-side and passenger-side air bag modules. Tighten mounting bolts to specification. See TORQUE SPECIFICATIONS . Connect positive battery cable. Connect negative battery cable. Perform SYSTEM OPERATION CHECK . Program radio station frequencies.
- Disconnect negative battery cable. Wait at least one minute. This is the time required for back-up power supply in diagnostic monitor to deplete its stored energy. Remove air bag simulators.
- Install driver-side and passenger-side air bag modules. Tighten mounting bolts to specification. See TORQUE SPECIFICATIONS . Connect positive battery cable. Perform SYSTEM OPERATION CHECK .
- Disconnect negative battery cable. Wait at least one minute. This is the time required for back-up power supply in diagnostic monitor to deplete its stored energy. Remove air bag simulator(s).
- Install driver-side and passenger-side air bag modules. See DRIVER-SIDE AIR BAG MODULE and PASSENGER-SIDE AIR BAG MODULE
. Connect negative battery cable. Perform SYSTEM OPERATION CHECK . Program radio station frequencies.
- Disconnect negative battery cable. Wait at least one minute. This is the time required for back-up power supply in diagnostic monitor to deplete its stored energy. Remove air bag simulator(s).
- Install driver-side and passenger-side air bag modules. Tighten mounting bolts to specification. See TORQUE SPECIFICATIONS . Connect negative battery cable. Perform SYSTEM OPERATION CHECK .
- Disconnect negative battery cable. Wait at least 10 minutes. This is the time required for back-up power supply in diagnostic monitor to deplete its stored energy.
- Remove air bag simulators. Connect negative battery cable. Perform SYSTEM OPERATION CHECK .
AIR BAG SIMULATOR APPLICATION
| Application |
Driver Side |
Passenger Side |
| Aerostar |
105-R0011 |
.... |
| Aspire |
105-R0009 |
105-R0009 |
| "E" Series Van |
105-00010 |
105-00010 |
| Expedition |
105-00011 |
105-00010 |
| Explorer & Mountaineer |
105-0010 |
105-0010 |
| F-150 Pickup |
105-00011 |
105-00010 |
| Continental |
105-R0011 |
105-R0010 |
| Contour & Mystique |
105-00010 |
105-00010 |
| Cougar & Thunderbird |
105-R0010 |
105-R0010 |
| Crown Victoria & Grand Marquis |
105-R0010 |
105-R0010 |
| Escort & Tracer |
T96P-50-AH |
105-00010 |
| Mark VIII |
105-00010 |
105-00010 |
| Mustang |
105-R0010 |
105-R0010 |
| Probe |
105-00009 |
105-00009 |
| Ranger |
105-R0011 |
105-00012 |
| Sable & Taurus |
105-R0010 |
105-00080 |
| Town Car |
105-00010 |
105-00010 |
| Villager |
T94P-50-A |
T96P-50-A |
| Windstar |
105-00010 |
105-00010 |