LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2021 >> Sentra S >> Repair and Diagnosis >> Accessories & Equipment >> Headlights >> Exterior Lighting System - Led Headlamp (DTC/Circuit Diagnosis) >> DTC/Circuit Diagnosis >> Turn Signal Lamp Circuit >> Diagnosis Procedure

Diagnosis Procedure

  1. CHECK TURN SIGNAL LAMP BULB 

    Check the turn signal lamp bulb.

    NOTE: Except door mirror (side turn signal lamp).

    Is the inspection result normal?

    YES

    GO TO 2.

    NO

    Front turn signal lamp: Replace the corresponding front turn signal lamp bulb. Refer to Bulb Replacement .

    NO

    Rear turn signal lamp: Replace the corresponding license plate lamp bulb. Refer to Bulb Replacement .

  2. CHECK SYMPTOM 

    Check symptom (A or B)

    Symptom

    A

    All of turn signal lamp do not blink

    B

    Applicable side performs high flasher activation

    Which symptom is detected?

    A

    GO TO 3.

    B

    GO TO 5.

  3. CHECK FUSE 
    1. Ignition switch OFF.
    2. Check if the following BCM fuse or fusible link are blown:

      Component

      Location

      Fuse No.

      Capacity

      BCM

      Fuse block (J/B)

      41

      5 A

      32

      10 A

    Is the fuse blown (open)?

    YES

    Replace the blown fuse or fusible link after repairing the affected circuit.

    NO

    GO TO 4.

  4. CHECK BCM POWER SUPPLY (TURN SIGNAL LAMP) 
    1. Disconnect BCM connector.
    2. Check voltage between BCM harness connector and ground.

      +

      -

      Voltage

      (Approx.)

      BCM

      Connector

      Terminal

      M84

      7

      Ground

      Battery voltage

      M20

      133

    Is the inspection result normal?

    YES

    Replace BCM. Refer to Removal and Installation .

    NO

    Repair or replace harness.

  5. CHECK TURN SIGNAL LAMP OUTPUT VOLTAGE 
    1. Ignition switch OFF.
    2. Disconnect the following connectors:
      • Front combination lamp LH
      • Front combination lamp RH
      • Door mirror LH
      • Door mirror RH
      • Rear combination lamp LH (body side)
      • Rear combination lamp RH (body side)
    3. Ignition switch ON.
    4. With operating the turn signal switch, check voltage between BCM harness connector and ground.
      Front turn signal lamp

      +

      -

      Condition

      Voltage

      (Approx.)

      BCM

      Connector

      Terminal

      RH

      M142

      116

      Ground

      Turn signal switch

      Right

      Blinking : Battery voltage

      Center

      0 V

      LH

      128

      Left

      Blinking : Battery voltage

      Center

      0 V
      Side turn signal lamp

      +

      -

      Condition

      Voltage

      (Approx.)

      BCM

      Connector

      Terminal

      RH

      M84

      1

      Ground

      Turn signal switch

      Right

      Blinking : Battery voltage

      Center

      0 V

      LH

      21

      Left

      Blinking : Battery voltage

      Center

      0 V
      Rear turn signal lamp

      +

      -

      Condition

      Voltage

      (Approx.)

      BCM

      Connector

      Terminal

      RH

      M21

      159

      Ground

      Turn signal switch

      Right

      Blinking : Battery voltage

      Center

      0 V

      LH

      151

      Left

      Blinking : Battery voltage

      Center

      0 V

    Is the inspection result normal?

    YES

    GO TO 7.

    NO

    GO TO 6.

  6. CHECK TURN SIGNAL LAMP POWER SUPPLY CIRCUIT (SHORT) 
    1. Ignition switch OFF.
    2. Disconnect BCM connector.
    3. Check continuity between BCM harness connector and ground.
      Front turn signal lamp

      BCM

      --

      Continuity

      Connector

      Terminal

      RH

      M142

      116

      Ground

      No

      LH

      128
      Side turn signal lamp

      BCM

      --

      Continuity

      Connector

      Terminal

      RH

      M84

      1

      Ground

      No

      LH

      21
      Rear turn signal lamp

      BCM

      --

      Continuity

      Connector

      Terminal

      RH

      M21

      159

      Ground

      No

      LH

      151

    Is the inspection result normal?

    YES

    Replace BCM. Refer to Removal and Installation .

    NO

    Repair or replace harness.

  7. CHECK TURN SIGNAL LAMP POWER SUPPLY CIRCUIT (OPEN) 
    1. Ignition switch OFF.
    2. Disconnect BCM connector.
    3. Check continuity between BCM harness connector and each turn signal lamp harness connector.
      Front turn signal lamp

      BCM

      Front combination lamp

      Continuity

      Connector

      Terminal

      Connector

      Terminal

      RH

      M142

      116

      E38

      2

      Yes

      LH

      128

      E37
      Side turn signal lamp (with intelligent around view monitor)

      BCM

      Door mirror

      Continuity

      Connector

      Terminal

      Connector

      Terminal

      RH

      M84

      1

      D106

      11

      Yes

      LH

      21

      D7
      Side turn signal lamp (without intelligent around view monitor)

      BCM

      Door mirror

      Continuity

      Connector

      Terminal

      Connector

      Terminal

      RH

      M84

      1

      D113

      1

      Yes

      LH

      21

      D4
      Rear turn signal lamp

      BCM

      Rear combination lamp (body side)

      Continuity

      Connector

      Terminal

      Connector

      Terminal

      RH

      M21

      159

      B42

      1

      Yes

      LH

      151

      B25

    Is the inspection result normal?

    YES

    GO TO 8.

    NO

    Repair or replace harness.

  8. CHECK TURN SIGNAL LAMP GROUND CIRCUIT 

    Check continuity between each turn signal lamp harness connector and ground.

    Front turn signal lamp

    Front combination lamp

    --

    Continuity

    Connector

    Terminal

    RH

    E38

    1

    Ground

    Yes

    LH

    E37
    Side turn signal lamp (with intelligent around view monitor)

    Door mirror

    --

    Continuity

    Connector

    Terminal

    RH

    D106

    12

    Ground

    Yes

    LH

    D7
    Side turn signal lamp (without intelligent around view monitor)

    Door mirror

    --

    Continuity

    Connector

    Terminal

    RH

    D113

    5

    Ground

    Yes

    LH

    D4
    Rear turn signal lamp

    Rear combination lamp (body side)

    --

    Continuity

    Connector

    Terminal

    RH

    B42

    4

    Ground

    Yes

    LH

    B25

    Is the inspection result normal?

    YES

    Front turn signal lamp: Check the corresponding front turn signal lamp bulb socket or harness. Repair or replace if necessary.

    YES

    Side turn signal lamp: Replace the corresponding side turn signal lamp. Refer to Removal and Installation .

    YES

    Rear turn signal lamp: Check the corresponding rear turn signal lamp bulb socket or harness. Repair or replace if necessary.

    NO

    Repair or replace harness.

scientia non olet · About LEMON Manuals