Detailed Procedure

WITH CONSULT

1. Start engine.
2. Check that the testing conditions are met. Refer to Component Function Check .
3. Select "A/F ALPHA-B1" and "A/F ALPHA-B2" in "SPEC" of "DATA MONITOR" mode, and check that each indication is within the SP value.
   NOTE: Check "A/F ALPHA-B1" and "A/F ALPHA-B2" for approximately 1 minute because they may fluctuate. It is NG if the indication is out of the SP value even a little.

Is the measurement value within the SP value?

YES

GO TO 14.

NO

Less than the SP value: GO TO 2.

NO

More than the SP value: GO TO 3.

Select "B/FUEL SCHDL" in "SPEC" of "DATA MONITOR" mode, and check that the indication is within the SP value.

Is the measurement value within the SP value?

YES

GO TO 4.

NO

More than the SP value: GO TO 16.

Select "B/FUEL SCHDL" in "SPEC" of "DATA MONITOR" mode, and check that the indication is within the SP value.

Is the measurement value within the SP value?

YES

GO TO 6.

NO

More than the SP value: GO TO 6.

NO

Less than the SP value: GO TO 22.

1. Stop the engine.
2. Disconnect PCV hose, and then plug it.
3. Start engine.
4. Select "A/F ALPHA-B1" and "A/F ALPHA-B2" in "SPEC" of "DATA MONITOR" mode, and check that each indication is within the SP value.

Is the measurement value within the SP value?

YES

GO TO 5.

NO

GO TO 6.

1. Stop the engine.
2. Change engine oil.
   NOTE: This symptom may occur when a large amount of gasoline is mixed with engine oil because of driving conditions (such as when engine oil temperature does not rise enough since a journey distance is too short during winter). The symptom will not be detected after changing engine oil or changing driving conditions.

INSPECTION END

1. Perform "POWER BALANCE" in "ACTIVE TEST" mode.
2. Check that each cylinder produces a momentary engine speed drop.

Is the inspection result normal?

YES

GO TO 9.

NO

GO TO 7.

Check the following below.

• Ignition coil and its circuit (Refer to Component Function Check .)
• Fuel injector and its circuit (Refer to Component Function Check .)
• Intake air leakage
• Low compression pressure (Refer to Inspection .)

Is the inspection result normal?

YES

Replace fuel injector and then GO TO 8.

NO

Repair or replace malfunctioning part and then GO TO 8.

1. Start engine.
2. Select "A/F ALPHA-B1" and "A/F ALPHA-B2" in "SPEC" of "DATA MONITOR" mode, and check that each indication is within the SP value.

Is the measurement value within the SP value?

YES

INSPECTION END

NO

GO TO 9.

Perform all DTC CONFIRMATION PROCEDURE related with A/F sensor 1.

• For DTC P0130, P0150, refer to DTC Description .
• For DTC P0131, P0151, refer to DTC Description .
• For DTC P0132, P0152, refer to DTC Description .
• For DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, refer to DTC Description .
• For DTC P2096, P2097, P2098, P2099 refer to DTC Description .

Are any DTCs detected?

YES

GO TO 10.

NO

GO TO 12.

Perform Diagnosis Procedure according to corresponding DTC.

GO TO 11.

1. Start engine.
2. Select "A/F ALPHA-B1" and "A/F ALPHA-B2" in "SPEC" of "DATA MONITOR" mode, and check that each indication is within the SP value.

Is the measurement value within the SP value?

YES

INSPECTION END

NO

GO TO 12.

1. Stop the engine.
2. Disconnect ECM harness connector. Check pin terminal and connector for damage, and then reconnect it.

GO TO 13.

1. Start engine.
2. Select "A/F ALPHA-B1" and "A/F ALPHA-B2" in "SPEC" of "DATA MONITOR" mode, and check that each indication is within the SP value.

Is the measurement value within the SP value?

YES

INSPECTION END

NO

Detect malfunctioning part according to Symptom Table .

Select "B/FUEL SCHDL" in "SPEC" of "DATA MONITOR" mode, and check that the indication is within the SP value.

Is the measurement value within the SP value?

YES

INSPECTION END

NO

More than the SP value: GO TO 15.

NO

Less than the SP value: GO TO 22.

1. Check for the cause of large engine friction. Refer to the following.
   • Engine oil level is too high
   • Engine oil viscosity
   • Belt tension of power steering, alternator, A/C compressor, etc. is excessive
   • Noise from engine
   • Noise from transmission, etc.
2. Check for the cause of insufficient combustion. Refer to the following.
   • Valve clearance malfunction
   • Intake valve timing control function malfunction
   • Camshaft sprocket installation malfunction, etc.

Repair or replace malfunctioning part, and then GO TO 27.

Check for the cause of uneven air flow through mass air flow sensor. Refer to the following.

• Crushed air ducts
• Malfunctioning seal of air cleaner element
• Uneven dirt of air cleaner element
• Improper specification of intake air system

Is the inspection result normal?

YES

GO TO 18.

NO

Repair or replace malfunctioning part, and then GO TO 17.

Select "A/F ALPHA-B1", "A/F ALPHA-B2" and "B/FUEL SCHDL" in "SPEC" of "DATA MONITOR" mode, and check that each indication is within the SP value.

Is the measurement value within the SP value?

YES

INSPECTION END

NO

"B/FUEL SCHDL" is more, "A/F ALPHA-B1" and "A/F ALPHA-B2" are less than the SP value: GO TO 18.

1. Stop the engine.
2. Disconnect mass air flow sensor harness connector. Check pin terminal and connector for damage and then reconnect it again.

GO TO 19.

1. Start engine.
2. Select "A/F ALPHA-B1" and "A/F ALPHA-B2" in "SPEC" of "DATA MONITOR" mode, and check that each indication is within the SP value.

Is the measurement value within the SP value?

YES

Detect malfunctioning part of mass air flow sensor circuit and repair it. Refer to Diagnosis Procedure . Then GO TO 26.

NO

GO TO 20.

Select "MAS A/F SE-B1" in "SPEC" of "DATA MONITOR" mode, and check that the indication is within the SP value.

Is the measurement value within the SP value?

YES

GO TO 21.

NO

More than the SP value: Replace malfunctioning mass air flow sensor, and then GO TO 26.

1. Replace ECM.
2. Perform Description .

GO TO 26.

Check for the cause of uneven air flow through mass air flow sensor. Refer to the following.

• Crushed air ducts
• Malfunctioning seal in air cleaner element
• Uneven dirt in air cleaner element
• Improper specification in intake air system

Is the inspection result normal?

YES

GO TO 24.

NO

Repair or replace malfunctioning part, and then GO TO 23.

Select "B/FUEL SCHDL" in "SPEC" of "DATA MONITOR" mode, and check that the indication is within the SP value.

Is the measurement value within the SP value?

YES

INSPECTION END

NO

Less than the SP value: GO TO 24.

Select "MAS A/F SE-B1" in "SPEC" of "DATA MONITOR" mode, and check that the indication is within the SP value.

Is the measurement value within the SP value?

YES

GO TO 25.

NO

Less than the SP value: Replace malfunctioning mass air flow sensor, and then GO TO 27.

Check for the cause of air leakage after the mass air flow sensor. Refer to the following.

• Disconnection, looseness, and cracks in air duct
• Looseness of oil filler cap
• Disconnection of oil level gauge
• Open stuck, breakage, hose disconnection, or cracks in PCV valve
• Disconnection or cracks in EVAP purge hose, stuck open EVAP canister purge volume control solenoid valve
• Malfunctioning seal in rocker cover gasket
• Disconnection, looseness, or cracks in hoses, such as a vacuum hose, connecting to intake air system parts
• Malfunctioning seal in intake air system, etc.

GO TO 27.

Select "A/F ALPHA-B1", "A/F ALPHA-B2" and "B/FUEL SCHDL" in "SPEC" of "DATA MONITOR" mode, and check that each indication is within the SP value.

Is the measurement value within the SP value?

YES

INSPECTION END

NO

Detect malfunctioning part according to Symptom Table .

Select "B/FUEL SCHDL" in "SPEC" of "DATA MONITOR" mode, and then check that the indication is within the SP value.

Is the measurement value within the SP value?

YES

INSPECTION END

NO

Detect malfunctioning part according to Symptom Table .