Data Monitor
X: Standard, --: Not applicable,
: Option
|
Monitored item (Unit) |
Monitor Item Selection |
Remarks |
|||
|
ECU INPUT SIGNALS |
MAIN SIGNALS |
SELECTION FROM ITEM |
|||
|
VHCL/S SE-A/T |
(km/h or mph) |
X |
X |
|
Displays the vehicle speed calculated by the TCM from the output shaft revolution. |
|
ESTM VSP SIG |
(km/h or mph) |
X |
-- |
|
Displays the vehicle speed signal received via CAN communication. |
|
OUTPUT REV |
(rpm) |
X |
X |
|
Displays the output speed calculated from the pulse signal of output speed sensor. |
|
INPUT SPEED |
(rpm) |
X |
X |
|
Displays the input speed calculated from front sun gear revolution and front carrier revolution. |
|
F SUN GR REV |
(rpm) |
-- |
-- |
|
Displays the front sun gear revolution calculated from the pulse signal of input speed sensor 1. |
|
F CARR GR REV |
(rpm) |
-- |
-- |
|
Displays the front carrier gear revolution calculated from the pulse signal of input speed sensor 2. |
|
ENGINE SPEED |
(rpm) |
X |
X |
|
Displays the engine speed received via CAN communication. |
|
TC SLIP SPEED |
(rpm) |
-- |
X |
|
Displays the revolution difference between input speed and engine speed. |
|
ACCELE POSI |
(0.0/8) |
X |
-- |
|
Displays the accelerator position estimated value received via CAN communication. |
|
THROTTLE POSI |
(0.0/8) |
X |
X |
|
Displays the throttle position received via CAN communication. |
|
ATF TEMP 1 |
(deg.C or deg.F) |
X |
X |
|
Displays the ATF temperature of oil pan calculated from the signal voltage of A/T fluid temperature sensor. |
|
ATF TEMP 2 |
(deg.C or deg.F) |
X |
X |
|
Displays the ATF temperature estimated value of torque converter outlet calculated from the signal voltage of A/T fluid temperature sensor. |
|
ATF TEMP SE 1 |
(V) |
-- |
-- |
|
Displays the signal voltage of A/T fluid temperature sensor. |
|
BATTERY VOLT |
(V) |
X |
-- |
|
Displays the power supply voltage of TCM. |
|
LINE PRES SOL |
(A) |
-- |
X |
|
Displays the command current from TCM to the line pressure solenoid. |
|
TCC SOLENOID |
(A) |
-- |
X |
|
Displays the command current from TCM to the torque converter clutch solenoid. |
|
L/B SOLENOID |
(A) |
-- |
X |
|
Displays the command current from TCM to the low brake solenoid. |
|
FR/B SOLENOID |
(A) |
-- |
X |
|
Displays the command current from TCM to the front brake solenoid. |
|
HLR/C SOL |
(A) |
-- |
X |
|
Displays the command current from TCM to the high and low reverse clutch solenoid. |
|
I/C SOLENOID |
(A) |
-- |
X |
|
Displays the command current from TCM to the input clutch solenoid. |
|
D/C SOLENOID |
(A) |
-- |
X |
|
Displays the command current from TCM to the direct clutch solenoid. |
|
2346/B SOL |
(A) |
-- |
X |
|
Displays the command current from TCM to the 2346 brake solenoid. |
|
L/P SOL MON |
(A) |
-- |
-- |
|
Monitors the command current from TCM to the line pressure solenoid, and displays the monitor value. |
|
TCC SOL MON |
(A) |
-- |
-- |
|
Monitors the command current from TCM to the torque converter clutch solenoid, and displays the monitor value. |
|
L/B SOL MON |
(A) |
-- |
-- |
|
Monitors the command current from TCM to the low brake solenoid, and displays the monitor value. |
|
FR/B SOL MON |
(A) |
-- |
-- |
|
Monitors the command current from TCM to the front brake solenoid, and displays the monitor value. |
|
HLR/C SOL MON |
(A) |
-- |
-- |
|
Monitors the command current from TCM to the high and low reverse clutch solenoid, and displays the monitor value. |
|
I/C SOL MON |
(A) |
-- |
-- |
|
Monitors the command current from TCM to the input clutch solenoid, and displays the monitor value. |
|
D/C SOL MON |
(A) |
-- |
-- |
|
Monitors the command current from TCM to the direct clutch solenoid, and displays the monitor value. |
|
2346/B SOL MON |
(A) |
-- |
-- |
|
Monitors the command current from TCM to the 2346 brake solenoid, and displays the monitor value. |
|
GEAR RATIO |
-- |
X |
|
Displays the gear ratio calculated from input speed and output speed. |
|
|
ENGINE TORQUE |
(Nm) |
-- |
-- |
|
Displays the engine torque estimated value received via CAN communication. |
|
ENG TORQUE D |
(Nm) |
-- |
-- |
|
Displays the engine torque estimated value reflected the requested torque of each control unit received via CAN communication. |
|
INPUT TRQ S |
(Nm) |
-- |
-- |
|
Displays the input torque using for the oil pressure calculation process of shift change control. |
|
INPUT TRQ L/P |
(Nm) |
-- |
-- |
|
Displays the input torque using for the oil pressure calculation process of line pressure control. |
|
TRGT PRES L/P |
(kPa, kg/cm 2 or psi) |
-- |
-- |
|
Displays the target oil pressure value of torque converter clutch solenoid valve calculated by the oil pressure calculation process of lock-up control. |
|
TRGT PRES TCC |
(kPa, kg/cm 2 or psi) |
-- |
-- |
|
Displays the target oil pressure value of torque converter clutch solenoid valve calculated by the oil pressure calculation process of shift change control. |
|
TRGT PRES L/B |
(kPa, kg/cm 2 or psi) |
-- |
-- |
|
Displays the target oil pressure value of low brake solenoid valve calculated by the oil pressure calculation process of shift change control. |
|
TRGT PRE FR/B |
(kPa, kg/cm 2 or psi) |
-- |
-- |
|
Displays the target oil pressure value of front brake solenoid valve calculated by the oil pressure calculation process of shift change control. |
|
TRG PRE HLR/C |
(kPa, kg/cm 2 or psi) |
-- |
-- |
|
Displays the target oil pressure value of high and low reverse clutch solenoid valve calculated by the oil pressure calculation process of shift change control. |
|
TRGT PRES I/C |
(kPa, kg/cm 2 or psi) |
-- |
-- |
|
Displays the target oil pressure value of input clutch solenoid valve calculated by the oil pressure calculation process of shift change control. |
|
TRGT PRES D/C |
(kPa, kg/cm 2 or psi) |
-- |
-- |
|
Displays the target oil pressure value of direct clutch solenoid valve calculated by the oil pressure calculation process of shift change control. |
|
TRG PRE 2346/B |
(kPa, kg/cm 2 or psi) |
-- |
-- |
|
Displays the target oil pressure value of 2346 brake solenoid valve calculated by the oil pressure calculation process of shift change control. |
|
SHIFT PATTERN |
-- |
-- |
|
Displays the gear change data using the shift pattern control. |
|
|
VEHICLE SPEED |
(km/h or mph) |
-- |
-- |
|
Displays the vehicle speed for control using the control of TCM. |
|
G SEN SLOPE |
(%) |
X |
-- |
|
Displays the inclination angle calculated by the G sensor signal received via CAN communication. |
|
RANGE SW 4 |
(ON/OFF) |
X |
-- |
|
Displays the operation status of transmission range switch 4. |
|
RANGE SW 3 |
(ON/OFF) |
X |
-- |
|
Displays the operation status of transmission range switch 3. |
|
RANGE SW 2 |
(ON/OFF) |
X |
-- |
|
Displays the operation status of transmission range switch 2. |
|
RANGE SW 1 |
(ON/OFF) |
X |
-- |
|
Displays the operation status of transmission range switch 1. |
|
SFT DWN ST SW |
(ON/OFF) |
X |
-- |
|
|
|
SFT UP ST SW |
(ON/OFF) |
X |
-- |
|
|
|
DOWN SW LEVER |
(ON/OFF) |
X |
-- |
|
Displays the operation status of selector lever (down switch). |
|
UP SW LEVER |
(ON/OFF) |
X |
-- |
|
Displays the operation status of selector lever (up switch). |
|
NON M-MODE SW |
(ON/OFF) |
X |
-- |
|
Displays whether the selector lever is in any position other than manual shift gate position. |
|
MANU MODE SW |
(ON/OFF) |
X |
-- |
|
Displays whether the selector lever is in the manual shift gate position. |
|
TOW MODE SW |
(ON/OFF) |
-- |
-- |
|
Displays the reception status of tow mode switch signal received via CAN communication. |
|
DS RANGE |
(ON/OFF) |
-- |
-- |
|
|
|
1 POSITION SW |
(ON/OFF) |
X |
-- |
|
|
|
OD CONT SW |
(ON/OFF) |
X |
-- |
|
|
|
BRAKESW |
(ON/OFF) |
X |
-- |
|
Displays the reception status of stop lamp switch signal received via CAN communication. |
|
POWERSHIFT SW |
(ON/OFF) |
X |
-- |
|
|
|
ASCD-OD CUT |
(ON/OFF) |
X |
-- |
|
Displays the reception status of ASCD OD cancel request signal received via CAN communication. |
|
ASCD-CRUISE |
(ON/OFF) |
X |
-- |
|
Displays the reception status of ASCD operation signal received via CAN communication. |
|
ABS SIGNAL |
(ON/OFF) |
X |
-- |
|
Displays the reception status of ABS operation signal received via CAN communication. |
|
TCS GR/P KEEP |
(ON/OFF) |
X |
-- |
|
Displays the reception status of TCS gear keep request signal received via CAN communication. |
|
TCS SIGNAL 2 |
(ON/OFF) |
X |
-- |
|
Displays whether the reception value of A/T shift schedule change demand signal received via CAN communication is "cold". |
|
TCS SIGNAL 1 |
(ON/OFF) |
X |
-- |
|
Displays whether the reception value of A/T shift schedule change demand signal received via CAN communication is "warm". |
|
LOW/B PARTS |
(FAIL/NOTFAIL) |
-- |
-- |
|
Displays whether the identified malfunction point judged by TCM is the related parts of low brake. |
|
HC/IC/FRB PARTS |
(FAIL/NOTFAIL) |
-- |
-- |
|
Displays whether the identified malfunction point judged by TCM is the related parts of high and low reversed clutch, input clutch or front brake. |
|
IC/FRB PARTS |
(FAIL/NOTFAIL) |
-- |
-- |
|
Displays whether the identified malfunction point judged by TCM is the related parts of input clutch or front brake. |
|
HLR/C PARTS |
(FAIL/NOTFAIL) |
-- |
-- |
|
Displays whether the identified malfunction point judged by TCM is the related parts of high and low reversed clutch. |
|
W/O THL POS |
(ON/OFF) |
X |
-- |
|
Displays the kickdown condition signal status received via CAN communication. |
|
CLSD THL POS |
(ON/OFF) |
X |
-- |
|
Displays the idling status signal status received via CAN communication. |
|
DRV CST JUDGE |
(DRIVE/COAST) |
-- |
-- |
|
Displays the judgment results of "driving" or "coasting" judged by TCM. |
|
SHIFT IND SIGNAL |
-- |
-- |
|
Displays the transmission value of shift position signal transmitted via CAN communication. |
|
|
STARTER RELAY |
(ON/OFF) |
-- |
-- |
|
Displays the command status from TCM to starter relay. |
|
F-SAFE IND/L |
(ON/OFF) |
-- |
-- |
|
Displays the transmission status of A/T CHECK indicator lamp signal transmitted via CAN communication. |
|
ATF WARN LAMP |
(ON/OFF) |
-- |
-- |
|
Displays the transmission status of ATF temperature signal transmitted via CAN communication. |
|
MANU MODE IND |
(ON/OFF) |
-- |
-- |
|
Displays the transmission status of manual mode signal transmitted via CAN communication. |
|
ON OFF SOL MON |
(ON/OFF) |
-- |
-- |
|
Monitors the command value from TCM to the anti-interlock solenoid, and displays the monitor status. |
|
START RLY MON |
(ON/OFF) |
-- |
-- |
|
Monitors the command value from TCM to the starter relay, and displays the monitor status. |
|
ON OFF SOL |
(ON/OFF) |
-- |
-- |
|
Displays the command status from TCM to anti-interlock solenoid. |
|
SLCT LVR POSI |
-- |
X |
|
Displays the shift positions recognized by TCM. |
|
|
GEAR |
-- |
X |
|
Displays the current transmission gear position recognized by TCM. |
|
|
NEXT GR POSI |
-- |
-- |
|
Displays the target gear position of gear change that is calculated based on the vehicle speed information and throttle information. |
|
|
SHIFT MODE |
-- |
-- |
|
Displays the transmission driving mode recognized by TCM. |
|
|
D/C PARTS |
(FAIL/NOTFAIL) |
-- |
-- |
|
Displays whether the identified malfunction point judged by TCM is the related parts of direct clutch. |
|
FR/B PARTS |
(FAIL/NOTFAIL) |
-- |
-- |
|
Displays whether the identified malfunction point judged by TCM is the related parts of front brake. |
|
2346/B PARTS |
(FAIL/NOTFAIL) |
-- |
-- |
|
Displays whether the identified malfunction point judged by TCM is the related parts of 2346 brake. |
|
2346B/DC PARTS |
(FAIL/NOTFAIL) |
-- |
-- |
|
Displays whether the identified malfunction point judged by TCM is the related parts of 2346 brake or direct clutch. |
|
N IDLE STATUS |
(ON/OFF) |
-- |
-- |
|
Displays the control status of idle neutral control. |