LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2021 >> NV2500 HD S >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 11 (Engine Control System (DTC/Circuit Diagnosis) (5.6L) (5 Of 6)) >> DTC/Circuit Diagnosis >> DTC P2138: App Sensor >> DTC Diagnosis Procedure

DTC Diagnosis Procedure

WARNING: This page is about a different variant/trim than selected.
  1. CHECK DTC PRIORITY 

    If DTC P2138 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.

    Is applicable DTC detected?

    YES

    Perform diagnosis of applicable. Refer to DTC Description .

    NO

    GO TO 2.

  2. CHECK ACCELERATOR PEDAL POSITION SENSOR 1 POWER SUPPLY CIRCUIT 
    1. Disconnect accelerator pedal position (APP) sensor harness connector.
    2. Turn ignition switch ON.
    3. Check the voltage between APP sensor harness connector and ground.

      APP sensor

      Ground

      Voltage (V)

      Connector

      Terminal

      E20

      2

      Ground

      Approx. 5

    Is the inspection result normal?

    YES

    GO TO 4.

    NO

    GO TO 3.

  3. DETECT MALFUNCTIONING PART 

    Check the following.

    • Loose or poor connection for each connector and harness
    • Harness for open or short between ECM and APP sensor

    Repair open circuit, short to ground or short to power in harness or connectors.

  4. CHECK APP SENSOR 2 POWER SUPPLY CIRCUIT-I 
    1. Turn ignition switch ON.
    2. Check the voltage between APP sensor harness connector and ground.

      APP sensor

      Ground

      Voltage (V)

      Connector

      Terminal

      E20

      1

      Ground

      Approx. 5

    Is the inspection result normal?

    YES

    GO TO 6.

    NO

    GO TO 5.

  5. CHECK SENSOR POWER SUPPLY 2 CIRCUIT 

    Perform Diagnosis Procedure .

    Is inspection result normal?

    YES

    Perform the trouble diagnosis for power supply circuit. Refer to DTC Diagnosis Procedure .

    NO

    Repair or replace error-detected parts.

  6. CHECK APP SENSOR GROUND CIRCUIT FOR OPEN AND SHORT 
    1. Turn ignition switch OFF.
    2. Disconnect ECM harness connector.
    3. Check the continuity between APP sensor harness connector and ECM harness connector.

      APP sensor

      ECM

      Continuity

      Connector

      Terminal

      Connector

      Terminal

      E20

      4

      E77

      151

      Existed

      5

      144
    4. Also check harness for short to ground and short to power.

    Is the inspection result normal?

    YES

    GO TO 8.

    NO

    GO TO 7.

  7. DETECT MALFUNCTIONING PART 

    Check the following.

    • Harness for open or short between ECM and accelerator pedal position sensor
    • Loose or poor connection for each connector and harness

    Repair open circuit, short to ground or short to power in harness or connectors.

  8. CHECK APP SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT 
    1. Check the continuity between APP sensor harness connector and ECM harness connector.

      APP sensor

      ECM

      Continuity

      Connector

      Terminal

      Connector

      Terminal

      E20

      3

      E77

      150

      Existed

      6

      143
    2. Also check harness for short to ground and short to power.

    Is the inspection result normal?

    YES

    GO TO 10.

    NO

    GO TO 9.

  9. DETECT MALFUNCTIONING PART 

    Check the following.

    • Harness for open or short between ECM and accelerator pedal position sensor
    • Loose or poor connection for each connector and harness

    Repair open circuit, short to ground or short to power in harness or connectors.

  10. CHECK APP SENSOR 

    Refer to Component Inspection (Accelerator Pedal Position Sensor) .

    Is the inspection result normal?

    YES

    INSPECTION END

    NO

    GO TO 11.

  11. REPLACE ACCELERATOR PEDAL ASSEMBLY 

    Replace accelerator pedal assembly. Refer to Removal and Installation .

    INSPECTION END

scientia non olet · About LEMON Manuals