Diagnosis Procedure

1. Turn ignition switch ON.
2. Select "DETE/CANCEL SW" and "SFT PN/N SW" in DATA MONITOR mode with CONSULT.
3. Check "DETE/CANCEL SW" and "SFT PN/N SW" indication under the following conditions.

   Monitor item	Condition		Indication
   DETE/CANCEL SW	CVT Shift selector	In any position other than P (Park)	ON
   		P (Park)	OFF
   SFT PN/N SW	CVT Shift selector	In any position other than P (Park)	OFF
   		P (Park)	ON

Is the inspection result normal?

YES

Refer to Intermittent Incident .

NO

If DETE/CANCEL SW is incorrect. GO TO 6.

NO

If SFT PN/N SW is incorrect. GO TO 2.

1. Turn ignition switch ON.
2. Check voltage between BCM harness connector and ground.

   (+)		(-)	Condition		Voltage (V) (Approx.)
   BCM
   Connector	Terminal
   M18	39	Ground	Selector lever	P or N position	Battery voltage
   				Other than above	0

Is the inspection result normal?

YES

GO TO 4.

NO

GO TO 3.

1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Disconnect transmission range switch connector.
4. Check continuity between transmission range switch harness connector and BCM harness connector.

   Transmission range switch		BCM		Continuity
   Connector	Terminal	Connector	Terminal
   F29	10	M18	39	Yes

5. Check continuity between transmission range switch harness connector and ground.

   Transmission range switch		Ground	Continuity
   Connector	Terminal
   F29	10		No

Is the inspection result normal?

YES

GO TO 5.

NO

Repair or replace harness.

1. Replace BCM. Refer to Removal and Installation .
2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.

Inspection End.

Check DTC in "Self Diagnostic Result" mode of "TCM" using CONSULT.

Is DTC detected?

YES

Perform the trouble diagnosis related to the detected DTC. Refer to DTC Logic (RE0F10J).

NO

Refer to Diagnosis Procedure (RE0F10J).

1. Turn ignition switch OFF.
2. Disconnect CVT shift selector (park position switch) connector.
3. Check voltage between CVT shift selector (park position switch) harness connector and ground.

   (+)		(-)	Voltage (V) (Approx.)
   CVT shift selector (park position switch)
   Connector	Terminal
   M78	5	Ground	Battery voltage

Is the inspection result normal?

YES

GO TO 8.

NO

GO TO 7.

1. Disconnect BCM connector.
2. Check continuity between CVT shift selector (park position switch) harness connector and BCM harness connector.

   CVT shift selector (park position switch)		BCM		Continuity
   Connector	Terminal	Connector	Terminal
   M78	5	M19	69	Yes

3. Check continuity between CVT shift selector (park position switch) harness connector and ground.

   CVT shift selector (park position switch)		Ground	Continuity
   Connector	Terminal
   M78	5		No

Is the inspection result normal?

YES

Replace BCM. Refer to Removal and Installation .

NO

Repair or replace harness.

1. Disconnect BCM connector and IPDM E/R connector.
2. Check continuity between CVT shift selector (park position switch) harness connector and BCM harness connector.

   CVT shift selector (park position switch)		BCM		Continuity
   Connector	Terminal	Connector	Terminal
   M78	6	M18	20	Yes

3. Check continuity between CVT shift selector (park position switch) harness connector and ground.

   CVT shift selector (park position switch)		Ground	Continuity
   Connector	Terminal
   M78	6		No

Is the inspection result normal?

YES

GO TO 9.

NO

Repair or replace harness.

Refer to Component Inspection .

Is the inspection result normal?

YES

GO TO 10.

NO

Replace CVT shift selector. Refer to Removal and Installation (RE0F10J).

1. Replace BCM. Refer to Removal and Installation .
2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.

Inspection End.