Removal and Installation: Installation

WARNING: This page is about a different car, the 2019 Nissan NV3500 HD and 2019 Nissan NV2500 HD. However, it is still accessible from the selected car via links, so may be relevant.

Note the following, and install in the reverse order of removal.

CAUTION:

Do not reuse copper washers.
Be careful not to damage A/T fluid cooler core.
Be careful not to damage condenser core, condenser pipe and liquid tank.

Check A/T fluid level. Refer to Inspection .

Refer to the following when installing A/T fluid cooler hoses.

Hose name	Hose end	Paint mark	Position of hose clamp ^*
A/T fluid cooler hose C	A/T fluid cooler tube A	Facing rightward	E
A/T fluid cooler hose C	A/T fluid cooler assembly	Facing rightward	E
A/T fluid cooler hose D	A/T fluid cooler tube B	Facing upward	B
A/T fluid cooler hose D	A/T fluid warmer	Facing upward	J
A/T fluid cooler hose E	A/T fluid warmer side	Facing upward	C
A/T fluid cooler hose E	A/T fluid cooler assembly	Facing rightward	D

*: Refer to the illustrations for the specific position each hose clamp tab.

The illustrations indicate the view from the hose ends.

Courtesy of NISSAN NORTH AMERICA, INC.

H	: Vehicle upper
I	: Vehicle front

When installing hose clamps center line of each hose clamp tab should be positioned as shown in the figure.

Insert A/T fluid cooler hoses according to dimension "L" described below.

A/T fluid cooler hose (1)	Insertion side tube (2)	Tube type	Dimension "L"
A/T fluid cooler hose C	A/T fluid cooler tube A	A	30-33 mm (1.18 in) [End reaches the 2-stage bulge (C).]
	A/T fluid cooler assembly
A/T fluid cooler hose D	A/T fluid cooler tube	A	30-33 mm (1.18 in) [End reaches the 2-stage bulge (C).]
	A/T fluid warmer tube
A/T fluid cooler hose E	A/T fluid warmer tube	B	Insert the hose until the hose touches the A/T fluid warmer.
	A/T fluid cooler assembly	A	30-33 mm (1.18 in) [End reaches the 2-stage bulge (C).]

Courtesy of NISSAN NORTH AMERICA, INC.

Set hose clamps (1) at the both ends of A/T fluid cooler hoses (2) with dimension "A" from the hose edge.

Courtesy of NISSAN NORTH AMERICA, INC.

Dimension "A"

: 5 - 9 mm (0.20 - 0.35 in)

Hose clamp should not interfere with the bulge of fluid cooler tube.

Note the following, and install in the reverse order of removal.

CAUTION:

Do not reuse copper washers.
Be careful not to damage A/T fluid cooler core.
Be careful not to damage condenser core, condenser pipe and liquid tank.

Check A/T fluid level. Refer to Inspection .

Refer to the following when installing A/T fluid cooler hoses.

Hose name	Hose end	Paint mark	Position of hose clamp ^*
A/T fluid cooler hose C	A/T fluid cooler tube A	Facing rightward	E
A/T fluid cooler hose C	A/T fluid cooler assembly	Facing rightward	E
A/T fluid cooler hose D	A/T fluid cooler tube B	Facing upward	B
A/T fluid cooler hose D	A/T fluid warmer	Facing upward	J
A/T fluid cooler hose E	A/T fluid warmer side	Facing upward	C
A/T fluid cooler hose E	A/T fluid cooler assembly	Facing rightward	D

*: Refer to the illustrations for the specific position each hose clamp tab.

The illustrations indicate the view from the hose ends.

Courtesy of NISSAN NORTH AMERICA, INC.

H	: Vehicle upper
I	: Vehicle front

When installing hose clamps center line of each hose clamp tab should be positioned as shown in the figure.

Insert A/T fluid cooler hoses according to dimension "L" described below.

A/T fluid cooler hose (1)	Insertion side tube (2)	Tube type	Dimension "L"
A/T fluid cooler hose C	A/T fluid cooler tube A	A	30-33 mm (1.18 in) [End reaches the 2-stage bulge (C).]
	A/T fluid cooler assembly
A/T fluid cooler hose D	A/T fluid cooler tube	A	30-33 mm (1.18 in) [End reaches the 2-stage bulge (C).]
	A/T fluid warmer tube
A/T fluid cooler hose E	A/T fluid warmer tube	B	Insert the hose until the hose touches the A/T fluid warmer.
	A/T fluid cooler assembly	A	30-33 mm (1.18 in) [End reaches the 2-stage bulge (C).]

Courtesy of NISSAN NORTH AMERICA, INC.

Set hose clamps (1) at the both ends of A/T fluid cooler hoses (2) with dimension "A" from the hose edge.

Courtesy of NISSAN NORTH AMERICA, INC.

Dimension "A"

: 5 - 9 mm (0.20 - 0.35 in)

Hose clamp should not interfere with the bulge of fluid cooler tube.

Note the following, and install in the reverse order of removal.

CAUTION:

Do not reuse copper washers.
Be careful not to damage A/T fluid cooler core.
Be careful not to damage condenser core, condenser pipe and liquid tank.

Check coolant level. Refer to Inspection .

Refer to the following when installing A/T fluid cooler hoses.

Hose name	Hose end	Paint mark	Position of hose clamp ^*
A/T fluid cooler hose C	A/T fluid cooler tube A	Facing rightward	E
A/T fluid cooler hose C	A/T fluid cooler assembly	Facing rightward	E
A/T fluid cooler hose D	A/T fluid cooler tube B	Facing upward	B
A/T fluid cooler hose D	A/T fluid warmer	Facing upward	J
A/T fluid cooler hose E	A/T fluid warmer side	Facing upward	C
A/T fluid cooler hose E	A/T fluid cooler assembly	Facing rightward	D

*: Refer to the illustrations for the specific position each hose clamp tab.

The illustrations indicate the view from the hose ends.

Courtesy of NISSAN NORTH AMERICA, INC.

H	: Vehicle upper
I	: Vehicle front

When installing hose clamps center line of each hose clamp tab should be positioned as shown in the figure.

Insert A/T fluid cooler hoses according to dimension "L" described below.

A/T fluid cooler hose (1)	Insertion side tube (2)	Tube type	Dimension "L"
A/T fluid cooler hose C	A/T fluid cooler tube A	A	30-33 mm (1.18 in) [End reaches the 2-stage bulge (C).]
	A/T fluid cooler assembly
A/T fluid cooler hose D	A/T fluid cooler tube	A	30-33 mm (1.18 in) [End reaches the 2-stage bulge (C).]
	A/T fluid warmer tube
A/T fluid cooler hose E	A/T fluid warmer tube	B	Insert the hose until the hose touches the A/T fluid warmer.
	A/T fluid cooler assembly	A	30-33 mm (1.18 in) [End reaches the 2-stage bulge (C).]

Courtesy of NISSAN NORTH AMERICA, INC.

Set hose clamps (1) at the both ends of A/T fluid cooler hoses (2) with dimension "A" from the hose edge.

Courtesy of NISSAN NORTH AMERICA, INC.

Dimension "A"

: 5 - 9 mm (0.20 - 0.35 in)

Hose clamp should not interfere with the bulge of fluid cooler tube.