DTC Diagnosis Procedure

WARNING: This page is about a different car, the 2019 Nissan NV3500 HD, 2019 Nissan NV2500 HD, and 2019 Nissan NV1500. However, it is still accessible from the selected car via links, so may be relevant.

NOTE: The Signal Tech II Tool [- (J-50190)] can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information.

Activate and display TPMS sensor IDs
Display tire pressure reported by the TPMS sensor
Read TPMS DTCs
Register TPMS sensor IDs

CHECK DATA MONITOR
With CONSULT
1. Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.
2. Stop the vehicle.
3. Select "AIR PRESS FL", "AIR PRESS FR", "AIR PRESS RR" and "AIR PRESS RL" in "Data Monitor" of "AIR PRESSURE MONITOR".
4. Within 5 minutes after vehicle is stopped, read the values displayed on CONSULT.
Are all tire pressures displayed 0 kPa (psi)?

YES

GO TO 2.

NO

GO TO 8.

CHECK RECEIVER POWER CIRCUIT CONTINUITY

Turn the ignition switch OFF.
Disconnect low tire pressure warning control unit and tire pressure receiver connectors.

Check continuity between low tire pressure warning control unit connector and tire pressure receiver connectors.

Low tire pressure warning control unit		Tire pressure receiver		Continuity
Connector	Terminal	Connector	Terminal
M90	10	E43 (Front LH)	1	Yes
	9	E60 (Front RH)
	8	C109 (Rear LH)
	7	C110 (Rear RH)

Check continuity between low tire pressure warning control unit connector and ground.

Low tire pressure warning control unit		--	Continuity
Connector	Terminal
M90	10	Ground	No
	9
	8
	7

Is the inspection result normal?

YES

GO TO 3.

Repair or replace the malfunctioning harness or connector.

CHECK RECEIVER SIGNAL CIRCUIT

Check continuity between low tire pressure warning control unit connector and tire pressure receiver connectors.

Low tire pressure warning control unit		Tire pressure receiver		Continuity
Connector	Terminal	Connector	Terminal
M90	6	E43 (Front LH)	3	Yes
	5	E60 (Front RH)
	4	C109 (Rear LH)
	3	C110 (Rear RH)

Check the continuity between low tire pressure warning control unit connector and ground.

Low tire pressure warning control unit		--	Continuity
Connector	Terminal
M90	6	Ground	No
	5
	4
	3

Is the inspection result normal?

YES

GO TO 4.

Repair or replace the malfunctioning harness or connector.

CHECK RECEIVER SIGNAL SENSITIVITY CIRCUIT

Check continuity between low tire pressure warning control unit connector and tire pressure receiver connectors.

Low tire pressure warning control unit		Tire pressure receiver		Continuity
Connector	Terminal	Connector	Terminal
M90	22	E43 (Front LH)	2	Yes
	21	E60 (Front RH)
	20	C109 (Rear LH)
	19	C110 (Rear RH)

Check the continuity between low tire pressure warning control unit harness connector and ground.

Low tire pressure warning control unit		--	Continuity
Connector	Terminal
M90	22	Ground	No
	21
	20
	19

Is the inspection result normal?

YES

GO TO 5.

Repair or replace the malfunctioning harness or connector.

CHECK RECEIVER GROUND CIRCUIT

Check continuity between low tire pressure warning control unit connector and tire pressure receiver connectors.

Low tire pressure warning control unit		Tire pressure receiver		Continuity
Connector	Terminal	Connector	Terminal
M90	26	E43 (Front LH)	4	Yes
	25	E60 (Front RH)
	24	C109 (Rear LH)
	23	C110 (Rear RH)

Check the continuity between low tire pressure warning control unit harness connector and ground.

Low tire pressure warning control unit		--	Continuity
Connector	Terminal
M90	26	Ground	No
	25
	24
	23

Is the inspection result normal?

YES

GO TO 6.

Repair or replace the malfunctioning harness or connector.

CHECK TIRE PRESSURE RECEIVER POWER SUPPLY CIRCUIT

Connect low tire pressure warning control unit harness connector.
Turn the ignition switch ON.

Check voltage between tire pressure receiver connector and ground.

Tire pressure receiver		--	Voltage
Connector	Terminal
E43 (Front LH)	1	Ground	Battery voltage
E60 (Front RH)
C109 (Rear LH)
C110 (Rear RH)

Is the inspection result normal?

YES

GO TO 7.

Replace the low tire pressure warning control unit. Refer to Removal and Installation .

TIRE PRESSURE RECEIVER SIGNAL
Check tire pressure receiver signal. Refer to Diagnosis Procedure .

Is the inspection result normal?

YES

GO TO 8.

NO

Repair or replace malfunctioning components.
TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration. Refer to Work Procedure .

Is tire pressure sensor ID registration completed?

YES

GO TO 9.

NO

Replace applicable tire pressure sensor. Refer to Removal and Installation .

CHECK TIRE PRESSURE SIGNAL

With CONSULT

Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.
Stop the vehicle.
Select "AIR PRESS FL", "AIR PRESS FR", "AIR PRESS RR" and "AIR PRESS RL" in "Data Monitor" of "AIR PRESSURE MONITOR".

Within 5 minutes after vehicle stopped, check that the tire pressures are within specification. Refer to Tire .

Monitor item	Displayed value
AIR PRESS FL	Approximately equal to the indication on tire gauge value for front LH tire
AIR PRESS FR	Approximately equal to the indication on tire gauge value for front RH tire
AIR PRESS RR	Approximately equal to the indication on tire gauge value for rear RH tire
AIR PRESS RL	Approximately equal to the indication on tire gauge value for rear LH tire

Is the inspection result normal?

YES

Inspection End.

Replace the low tire pressure warning control unit. Refer to Removal and Installation .