Values on the Diagnosis Tool
|
Monitor item |
Display content |
Data monitor |
|
|
Condition |
Reference value in normal operation |
||
|
FR LH SENSOR |
Wheel speed |
0 [km/h (MPH)] |
Vehicle stopped |
|
Nearly matches the speed meter display (+/- 10% or less) |
Vehicle running (Note 1) |
||
|
FR RH SENSOR |
Wheel speed |
0 [km/h (MPH)] |
Vehicle stopped |
|
Nearly matches the speed meter display (+/- 10% or less) |
Vehicle running (Note 1) |
||
|
RR LH SENSOR |
Wheel speed |
0 [km/h (MPH)] |
Vehicle stopped |
|
Nearly matches the speed meter display (+/- 10% or less) |
Vehicle running (Note 1) |
||
|
RR RH SENSOR |
Wheel speed |
0 [km/h (MPH)] |
Vehicle stopped |
|
Nearly matches the speed meter display (+/- 10% or less) |
Vehicle running (Note 1) |
||
|
DECEL G-SEN |
Longitudinal acceleration detected by Decel G-Sensor |
Vehicle stopped |
Approx. 0 G |
|
Vehicle running |
-1.7 to 1.7 G |
||
|
FR RH IN SOL |
Operation status of each solenoid valve |
Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT) or actuator relay is inactive (in fail-safe mode) |
ON |
|
When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON) |
OFF |
||
|
FR RH OUT SOL |
Operation status of each solenoid valve |
Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT) or actuator relay is inactive (in fail-safe mode) |
ON |
|
When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON) |
OFF |
||
|
FR LH IN SOL |
Operation status of each solenoid valve |
Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT) or actuator relay is inactive (in fail-safe mode) |
ON |
|
When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON) |
OFF |
||
|
FR LH OUT SOL |
Operation status of each solenoid valve |
Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT) or actuator relay is inactive (in fail-safe mode) |
ON |
|
When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON) |
OFF |
||
|
RR RH IN SOL |
Operation status of each solenoid valve |
Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT) or actuator relay is inactive (in fail-safe mode) |
ON |
|
When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON) |
OFF |
||
|
RR RH OUT SOL |
Operation status of each solenoid valve |
Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT) or actuator relay is inactive (in fail-safe mode) |
ON |
|
When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON) |
OFF |
||
|
RR LH IN SOL |
Operation status of each solenoid valve |
Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT) or actuator relay is inactive (in fail-safe mode) |
ON |
|
When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON) |
OFF |
||
|
RR LH OUT SOL |
Operation status of each solenoid valve |
Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT) or actuator relay is inactive (in fail-safe mode) |
ON |
|
When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON) |
OFF |
||
|
EBD WARN LAMP |
EBD warning lamp (Note 2) |
When EBD warning lamp is ON |
ON |
|
When EBD warning lamp is OFF |
OFF |
||
|
STOP LAMP SW |
Stop lamp switch signal status |
When brake pedal is depressed |
ON |
|
When brake pedal is released |
OFF |
||
|
MOTOR RELAY |
Motor and motor relay operation |
When the motor relay and motor are operating |
ON |
|
When the motor relay and motor are not operating |
OFF |
||
|
ACTUATOR RLY |
Actuator relay operation |
When the actuator relay is operating |
ON |
|
When the actuator relay is not operating |
OFF |
||
|
ABS WARN LAMP |
ABS warning lamp (Note 2) |
When ABS warning lamp is ON |
ON |
|
When ABS warning lamp is OFF |
OFF |
||
|
OFF LAMP |
VDC OFF indicator lamp (Note 2) |
When VDC OFF indicator lamp is ON |
ON |
|
When VDC OFF indicator lamp is OFF |
OFF |
||
|
OFF SW |
VDC OFF switch ON/OFF |
VDC OFF switch ON (When VDC OFF indicator lamp is ON) |
ON |
|
VDC OFF switch OFF (When VDC OFF indicator lamp is OFF) |
OFF |
||
|
SLIP/VDC LAMP |
SLIP indicator lamp (Note 2) |
When SLIP indicator lamp is ON |
ON |
|
When SLIP indicator lamp is OFF |
OFF |
||
|
BATTERY VOLT |
Battery voltage supplied to the ABS actuator and electric unit (control unit) |
Ignition switch ON |
10 - 16 V |
|
GEAR |
Gear position determined by TCM |
1st gear 2nd gear 3rd gear 4th gear 5th gear |
1 2 3 4 5 |
|
ENGINE SPEED |
With engine running |
With engine stopped |
0 rpm |
|
Engine running |
Almost in accordance with tachometer display |
||
|
YAW RATE SEN |
Yaw rate detected by yaw rate/side/decel G sensor |
When vehicle is stopped |
Approx. 0 d/s |
|
When vehicle is turning |
-75 to 75 d/s |
||
|
R POSI SIG |
Transmission range switch signal ON/OFF condition |
A/T shift position = R position |
ON |
|
A/T shift position = other than R position |
OFF |
||
|
N POSI SIG |
Transmission range switch signal ON/OFF condition |
A/T shift position = N position |
ON |
|
A/T shift position = other than N position |
OFF |
||
|
CV1 |
VDC switch-over valve |
When actuator (switch-over valve) is active ("ACTIVE TEST" with CONSULT) or actuator relay is inactive (when in fail-safe mode) |
ON |
|
When actuator (switch-over valve) is not active and actuator relay is active (ignition switch ON) |
OFF |
||
|
CV2 |
VDC switch-over valve |
When actuator (switch-over valve) is active ("ACTIVE TEST" with CONSULT) or actuator relay is inactive (when in fail-safe mode) |
ON |
|
When actuator (switch-over valve) is not active and actuator relay is active (ignition switch ON) |
OFF |
||
|
SV1 |
VDC switch-over valve |
When actuator (switch-over valve) is active ("ACTIVE TEST" with CONSULT) or actuator relay is inactive (when in fail-safe mode) |
ON |
|
When actuator (switch-over valve) is not active and actuator relay is active (ignition switch ON) |
OFF |
||
|
SV2 |
VDC switch-over valve |
When actuator (switch-over valve) is active ("ACTIVE TEST" with CONSULT) or actuator relay is inactive (when in fail-safe mode) |
ON |
|
When actuator (switch-over valve) is not active and actuator relay is active (ignition switch ON) |
OFF |
||
|
STOP LAMP SW2 |
Stop lamp switch signal status |
When brake pedal is depressed |
ON |
|
When brake pedal is released |
OFF |
||
|
ACCEL POS SIG |
Throttle actuator opening/closing is displayed (linked with accelerator pedal) |
Accelerator pedal not depressed (ignition switch is ON) |
0 % |
|
Accelerator pedal depressed (ignition switch is ON) |
0 - 100 % |
||
|
SIDE G-SENSOR |
Transverse G detected by side G sensor |
Vehicle stopped |
Approx. 0 m/s 2 |
|
Vehicle turning right |
Negative value (m/s 2 ) |
||
|
Vehicle turning left |
Positive value (m/s 2 ) |
||
|
STR ANGLE SIG |
Steering angle detected by steering angle sensor |
Straight-ahead |
Approx. 0+/-2.5 deg. |
|
Steering wheel turned |
-720 to +720 deg. |
||
|
PRESS SENSOR |
Brake fluid pressure detected by pressure sensor |
With ignition switch turned ON and brake pedal released |
0 bar |
|
With ignition switch turned ON and brake pedal depressed |
-40 to 300 bar (Pressure increases according to pedal effort.) |
||
|
ACCUM PRESS SEN |
Accumulator pressure |
With ignition switch turned ON and brake pedal released |
0 bar |
|
With ignition switch turned ON and brake pedal depressed |
0 to 210 bar |
||
|
EBD SIGNAL |
EBD operation |
EBD is active |
ON |
|
EBD is inactive |
OFF |
||
|
ABS SIGNAL |
ABS operation |
ABS is active |
ON |
|
ABS is inactive |
OFF |
||
|
TCS SIGNAL |
TCS operation |
TCS is active |
ON |
|
TCS is inactive |
OFF |
||
|
VDC SIGNAL |
VDC operation |
VDC is active |
ON |
|
VDC is inactive |
OFF |
||
|
EBD FAIL SIG |
EBD fail-safe signal |
In EBD fail-safe |
ON |
|
EBD is normal |
OFF |
||
|
ABS FAIL SIG |
ABS fail-safe signal |
In ABS fail-safe |
ON |
|
ABS is normal |
OFF |
||
|
TCS FAIL SIG |
TCS fail-safe signal |
In TCS fail-safe |
ON |
|
TCS is normal |
OFF |
||
|
VDC FAIL SIG |
VDC fail-safe signal |
In VDC fail-safe |
ON |
|
VDC is normal |
OFF |
||
|
CRANKING SIG |
Crank operation |
Crank is active |
ON |
|
Crank is inactive |
OFF |
||
|
FLUID LEV SW |
Brake fluid level switch signal status |
When brake fluid level switch is ON |
ON |
|
When brake fluid level switch is OFF |
OFF |
||
|
PARK BRAKE SW |
Parking brake switch signal status |
Parking brake applied |
ON |
|
Parking brake released |
OFF |
||
|
STP ON RLY |
Stop lamp relay signal |
When stop lamp relay is ON |
ON |
|
When stop lamp relay is OFF |
OFF |
||
- 1: Confirm tire pressure is normal.
- 2: ON and OFF timing for warning lamp and indicator lamp.
- ABS warning lamp: Refer to Component Function Check .
- Brake warning lamp: Refer to Component Function Check .
- SLIP indicator lamp: Refer to Component Function Check .
- VDC OFF indicator lamp: Refer to Component Function Check .