LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2021 >> NV2500 HD S >> Repair and Diagnosis >> External Pages >> Different car >> Section 465 (SRS Airbag) >> Basic Inspection >> Collision Diagnosis >> For Frontal Collision >> SRS Inspection (For Frontal Collision)

SRS Inspection (For Frontal Collision)

WARNING: This page is about a different car, the 2019 Nissan NV3500 HD, 2019 Nissan NV2500 HD, and 2019 Nissan NV1500. However, it is still accessible from the selected car via links, so may be relevant.

Part

Inspection

Driver air bag module

If the driver air bag has deployed:

REPLACE

Install with new fasteners.

Front passenger air bag module

If the front passenger air bag has deployed:

REPLACE

Install with new fasteners.

Crash zone sensor

If any of the front air bags or seat belt pre-tensioners* have been activated:

REPLACE the crash zone sensor and bracket with new fasteners.

*: Confirm seat belt pre-tensioner activation using CONSULT only.

Seat belt pre-tensioner assemblies

(All applicable locations: buckle, retractor, lap outer)

If either the driver or passenger seat belt pre-tensioner* has been activated:

REPLACE all seat belt pre-tensioner assemblies with new fasteners.

*: Confirm seat belt pre-tensioner activation using CONSULT only.

Diagnosis sensor unit

If any of the SRS components have been activated:

REPLACE the diagnosis sensor unit.

Install with new fasteners.

Steering wheel
  1. Visually check steering wheel for deformities.
  2. Check harness (built into steering wheel) and connectors for damage, and terminals for deformities.
  3. Install driver air bag module into the steering wheel to check fit and alignment with the wheel.
  4. Check steering wheel for excessive free play.
  5. If no damage is found, reinstall.
  6. If damaged -- REPLACE.

Spiral cable

If the driver front air bag has deployed:

REPLACE the spiral cable.

Occupant classification system (Passenger seat)
  1. Remove passenger seat assembly.
  2. Check control unit case for dents, cracks of deformities.
  3. Check connectors for damage and terminals for deformities.
  4. Check seat frame and cushion pan for dents or deformities.
  5. If no damage is found, reinstall seat with new fasteners.
  6. If damaged -- REPLACE seat cushion assembly with new fasteners.

Harness and connectors
  1. Check connectors for poor connection, damage, and terminals for deformities.
  2. Check harness for binding, chafing, cuts, or deformities.
  3. If no damage is found, reinstall the harness and connectors.
  4. If damaged -- REPLACE the damaged harness. Do not attempt to repair, splice or modify any SRS harness.

Instrument panel assembly

If the passenger front air bag has deployed:

REPLACE the instrument panel assembly. (integrated type)


Part

Inspection

Driver air bag module

If the driver air bag has NOT been activated:

  1. Remove driver air bag module. Check harness cover and connectors for damage, terminals for deformities, and harness for binding.
  2. Install driver air bag module into the steering wheel to check fit and alignment with the wheel.
  3. If no damage is found, reinstall with new fasteners.
  4. If damaged -- REPLACE. Install driver air bag modules with new fasteners.

Front passenger air bag module

If the front passenger air bag has NOT been activated:

  1. Remove front passenger air bag module. Check harness cover and connectors for damage, terminals for deformities, and harness for binding.
  2. Install front passenger air bag module into the instrument panel to check fit with the instrument panel.
  3. If no damage is found, reinstall with new fasteners.
  4. If damaged -- REPLACE. Install front passenger air bag modules with new fasteners.

Crash zone sensor

If the front air bags or seat belt pre-tensioners have NOT been activated:

  1. Remove the crash zone sensor. Check harness connectors for damage, terminals for deformities, and harness for binding.
  2. Check for visible signs of damage (dents, cracks, deformation) of the crash zone sensor and bracket.
  3. Install the crash zone sensor to check fit.
  4. If no damage is found, reinstall with new fasteners.
  5. If damaged -- REPLACE the crash zone sensor and bracket with new fasteners.

Seat belt pre-tensioner assemblies

(All applicable locations: buckle, retractor, lap outer)

If the pre-tensioners have NOT been activated:

  1. Remove seat belt pre-tensioners.

    Check harness cover and connectors for damage, terminals for deformities, and harness for binding.

  2. Check belts for damage and anchors for loose mounting.
  3. Check retractor for smooth operation.
  4. Check seat belt adjuster for damage.
  5. Check for deformities of the center pillar inner.
  6. If no damage is found, reinstall seat belt pre-tensioner assembly with new fasteners.
  7. If damaged --REPLACE. Install the seat belt pre-tensioner assembly with new fasteners.

Diagnosis sensor unit

If none of the SRS components have been activated:

  1. Check case for dents, cracks or deformities.
  2. Check connectors for damage, and terminals for deformities.
  3. If no damage is found, reinstall with new fasteners.
  4. If damaged -- REPLACE. Install diagnosis sensor unit with new fasteners.

Steering wheel
  1. Visually check steering wheel for deformities.
  2. Check harness (built into steering wheel) and connectors for damage, and terminals for deformities.
  3. Install driver air bag module into the steering wheel to check fit and alignment with the wheel.
  4. Check steering wheel for excessive free play.
  5. If no damage is found, reinstall.
  6. If damaged -- REPLACE.

Spiral cable

If the driver front air bag has not deployed:

  1. Visually check spiral cable and combination switch for damage.
  2. Check connectors and protective tape for damage.
  3. Check steering wheel for noise, binding or heavy operation.
  4. If no damage is found, reinstall.
  5. If damaged -- REPLACE.

Occupant classification system (Passenger seat)
  1. Remove passenger seat assembly.
  2. Check control unit case for dents, cracks of deformities.
  3. Check connectors for damage and terminals for deformities.
  4. Check seat frame and cushion pan for dents or deformities.
  5. If no damage is found, reinstall seat with new fasteners.
  6. If damaged -- REPLACE seat cushion assembly with new fasteners.

Harness and connectors
  1. Check connectors for poor connection, damage, and terminals for deformities.
  2. Check harness for binding, chafing, cuts, or deformities.
  3. If no damage is found, reinstall the harness and connectors.
  4. If damaged ----REPLACE the damaged harness. Do not attempt to repair, splice or modify any SRS harness.

Instrument panel assembly

If the passenger front air bag has NOT deployed:

  1. Visually check instrument panel for damage.
  2. If no damage is found, reinstall the instrument panel assembly.
  3. If damaged--REPLACE the instrument panel assembly.
scientia non olet · About LEMON Manuals