Driving Condition

WARNING: This page is about a different car, the 2019 Infiniti QX60. However, it is still accessible from the selected car via links, so may be relevant.

Driving condition A

Driving condition A is the driving condition that provides warm-up.

In specific, count-up is performed when all of the following conditions are satisfied.

Engine speed is 400 RPM or more.
After start of the engine, the water temperature increased by 20 deg.C (36 deg.F) or more.
Water temperature was 70 deg.C (158 deg.F) or more.
The ignition switch was changed from ON to OFF.

NOTE:

If the same malfunction is detected regardless of the driving condition, reset the A counter.
When the above is satisfied without detecting the same malfunction, count up the A counter.
When MIL goes off due to the malfunction and the A counter reaches 40, the DTC is erased.

Driving condition B

Driving condition B is different by each DTC.

In specific, count-up is performed when the following conditions are satisfied.

DTC	Driving condition
P062F, P0740, P0743, P0778, P0779, P0863, P0890, P0962, P0963, P0966, P0967	Start the engine and let it idle for least 1 second.
U0073, U0100	Start the engine and let it idle for least 2 seconds.
P0711

Turn ignition switch OFF and leave the vehicle for 12 hours.
Start the engine.
NOTE: When starting the engine, CVT fluid temperature is less than 20 deg.C (68 deg.F).

Drive the vehicle for the total minutes specified in the Driving time column below with the following conditions satisfied.

Ignition voltage: 11 V or more
Selector lever: "D" position
Throttle position: 1% or more
Engine speed: 450 RPM
Vehicle speed: 10 km/h (7 MPH) or more

Table

CVT fluid temperature before engine start	Driving time
-40 deg.C (-40 deg.F) --31 deg.C (-23.8 deg.F)	20minutes or more
-30 deg.C (-22 deg.F) --21 deg.C (-5.8 deg.F)	18 minutes or more
-20 deg.C (-4 deg.F) --11 deg.C (-12.2 deg.F)	14 minutes or more
-10 deg.C (14 deg.F) --1 deg.C (30.2 deg.F)	10minutes or more
0 deg.C (32 deg.F) - 9 deg.C (48.2 deg.F)	7 minutes or more

CVT fluid temperature rises to 20 deg.C (68 deg.F) or more.

DTC	Driving condition
P0712	Start the engine and let it idle for least 5 seconds.
P0705	Turn ignition switch ON. Shift the selector lever through entire positions from "P" to "D". (Hold the selector lever at each position for 2 seconds or more.)
P0706	Turn ignition switch ON. Shift the selector lever through entire positions from "P" to "D". (Hold the selector lever at each position for 30 seconds or more.)
P0713	Drive the vehicle for 5 seconds or more under the following conditions. Vehicle speed: 20 km/h (12 MPH) or more
P0715, P0716, P0717, P0791, P0792, P0793	Drive the vehicle for 5 seconds or more under the following conditions. Selector lever: "D" position Engine speed: 1, 200 RPM or more Vehicle speed: 40 km/h (25 MPH) or more
P0744	Drive the vehicle for 10 seconds or more under the following conditions. Selector lever: "D" position CVT fluid temperature: 20 deg.C (68 deg.F) or more Vehicle speed: 40 km/h (25 MPH) or more
P0746	Drive the vehicle for 5 seconds or more under the following conditions. Selector lever: "D" position Accelerator pedal position: 0.5/8 or more Vehicle speed: 40 km/h (25 MPH) or more
P0776	Drive the vehicle for 10 seconds or more under the following conditions. Selector lever: "D" position Accelerator pedal position: 1.0/8 or more Vehicle speed: 40 km/h (25 MPH) or more
P0841	Drive the vehicle for 5 seconds or more under the following conditions. Selector lever: "D" position Vehicle speed: 40 km/h (25 MPH) or more
P0847, P0848, P084C, P084D	Start the engine and wait for at least 10 seconds. CAUTION: When the ambient temperature is less than -20 deg.C (-4 deg.F) and the engine is cold, warm up the engine for approximately 5 minutes.
P0965	Drive the vehicle for 10 seconds or more under the following conditions. Vehicle speed: 40 km/h (25 MPH) or more
P2765, P2766, P2767	Drive the vehicle for 5 seconds or more under the following conditions. Selector lever: "D" position Engine speed: 1, 200 RPM or more Vehicle speed: 55 km/h (34 MPH) or more
P2813	Start the engine. Repeat D position creep start and a stop more than five times. Drive the vehicle for 30 seconds or more in total under the following conditions. Selector lever: "D" position Accelerator pedal position: 0.7/8 or more Vehicle speed: 40 km/h (25 MPH) or more
P2814, P2815	Start the engine. Shift the selector lever from N position to D and keep 5 seconds or more. Shift the selector lever from N position to R and keep 5 seconds or more. Shift the selector lever from P position to R and keep 5 seconds or more.

NOTE:

If the same malfunction is detected regardless of the driving condition, reset the B counter.
When the above is satisfied without detecting the same malfunction, count up the B counter.
When the B counter reaches 3 without malfunction, MIL goes off.
When the B counter is counted once without detecting the same malfunction after TCM memorizes DTC of the 1st trip, DTC of the 1st trip is erased.