LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2021 >> NV2500 HD S >> Repair and Diagnosis >> External Pages >> Different car >> Section 317 (Engine Control System (DTC/Circuit Diagnosis) (4.0L) (2 Of 4)) >> DTC/Circuit Diagnosis >> DTC P0138: Ho2S2 >> DTC Confirmation Procedure

DTC Confirmation Procedure

WARNING: This page is about a different car, the 2018 Nissan NV3500 HD, 2018 Nissan NV2500 HD, and 2018 Nissan NV1500. However, it is still accessible from the selected car via links, so may be relevant.
  1. PRECONDITIONING 

    If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

    1. Turn ignition switch OFF and wait at least 10 seconds.
    2. Turn ignition switch ON.
    3. Turn ignition switch OFF and wait at least 10 seconds.

    GO TO 2 .

  2. PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A 
    1. Start engine and warm it up to the normal operating temperature.
    2. Turn ignition switch OFF and wait at least 10 seconds.
    3. Turn ignition switch ON.
    4. Turn ignition switch OFF and wait at least 10 seconds.
    5. Start engine and keep the engine speed between 3, 500 and 4, 000 rpm for at least 1 minute under no load.
    6. Let engine idle for 2 minutes.
    7. Check 1st trip DTC.

    Is 1st trip DTC detected?

    YES

    Proceed to Diagnosis Procedure .

    NO

    SYMBOL With CONSULT: GO TO 3 .

    NO

    SYMBOL Without CONSULT: GO TO 5 .

  3. PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B 

    SYMBOL With CONSULT

    NOTE: For better results, perform "DTC WORK SUPPORT" at a temperature of 0 to 30 °C (32 to 86 °F).
    1. Select "DATA MONITOR" mode of "ENGINE" using CONSULT.
    2. Start engine and warm it up to the normal operating temperature.
    3. Turn ignition switch OFF and wait at least 10 seconds.
    4. Turn ignition switch ON.
    5. Turn ignition switch OFF and wait at least 10 seconds.
    6. Start engine and keep the engine speed between 3, 500 and 4, 000 rpm for at least 1 minute under no load.
    7. Let engine idle for 1 minute.
    8. Make sure that "COOLAN TEMP/S" indicates more than 70°C (158°F).

      If not, warm up engine and go to next step when "COOLAN TEMP/S" indication reaches 70°C (158°F).

    9. Open engine hood.
    10. Select "HO2S2 (B1) P1146" (for DTC P0138) or "HO2S2 (B2) P1166" (for DTC P0158) of "HO2S2" in "DTC WORK SUPPORT" mode of "ENGINE" using CONSULT.
    11. Start engine and follow the instruction of CONSULT display.
      NOTE: It will take at most 10 minutes until "COMPLETED" is displayed.
    12. Touch "SELF-DIAG RESULTS".

    Which is displayed on CONSULT screen?

    YES

    INSPECTION END

    NO

    Proceed to Diagnosis Procedure .

    CON NOT BE DIAGNOSED

    GO TO 4 .

  4. PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B AGAIN 
    1. Turn ignition switch OFF and leave the vehicle in a cool place (soak the vehicle).
    2. Perform DTC confirmation procedure again.

    GO TO 3 .

  5. PERFORM COMPONENT FUNCTION CHECK FOR MALFUNCTION B 

    SYMBOL Without CONSULT

    Perform component function check. Refer to Component Function Check .

    NOTE: Use component function check to check the overall function of the heated oxygen sensor 2 circuit. During this check, a 1st trip DTC might not be confirmed.

    Is the inspection result normal?

    YES

    INSPECTION END

    NO

    Proceed to Diagnosis Procedure .

scientia non olet · About LEMON Manuals