Diagnosis Procedure

WARNING: This page is about a different car, the 2018 Nissan Titan XD. However, it is still accessible from the selected car via links, so may be relevant.

CHECK DTC PRIORITY
1. Turn ignition switch ON.
2. Connect CONSULT and check for "ENGINE" diagnostic trouble codes.
3. Check for DTC P1191-00 being current on the CONSULT screen.
Is DTC P1191-00 detected as current?

YES

GO TO 2 .

NO

Refer to Intermittent Incident .
CHECK DTC PRIORITY
1. Turn ignition switch ON.
2. Connect CONSULT and check for "ENGINE" diagnostic trouble codes.
3. Are any of the following displayed as current on the CONSULT screen:
  - P1192-00
  - P1193
Is applicable DTC detected?

YES

Refer to DTC Index .

NO

GO TO 3 .
INSPECT TURBOCHARGER COMPRESSOR INTAKE PRESSURE/TEMPERATURE SENSOR AND CONNECTOR PINS
1. Turn ignition switch OFF.
2. Disconnect turbocharger compressor intake pressure/temperature sensor harness connector F105.
3. Inspect the harness connector and turbocharger compressor intake pressure/temperature sensor pins for the following:
  - Loose connector
  - Corroded pins
  - Bent or broken pins
  - Pushed back or expanded pins
  - Moisture in or on the connector
  - Missing or damaged connector seals
  - Dirt or debris on or in the connector pins
  - Connector shell broken
  - Wire insulation damage
  - Damaged connector locking tab
Is the inspection result normal?

YES

GO TO 4 .

NO

Repair or replace error-detected parts.
CHECK THE CIRCUIT RESPONSE
1. Turn ignition switch OFF.
2. Disconnect turbocharger compressor intake pressure/temperature sensor harness connector F105.
3. Turn ignition switch ON and wait 30 seconds.
4. Connect CONSULT and check for current "ENGINE" diagnostic trouble codes.
Did P1193-00 DTC become current?

YES

GO TO 5 .

NO

GO TO 6 .
CHECK THE CIRCUIT RESPONSE
1. Turn ignition switch OFF.
2. Connect a jumper wire between turbocharger compressor intake pressure/temperature sensor harness connector F105 terminal 3 and 4.
3. Turn ignition switch ON and wait 30 seconds.
4. Connect CONSULT and check for current "ENGINE" diagnostic trouble codes.
Did P1192-00 DTC become current?

YES

Replace turbocharger compressor intake pressure/temperature sensor. Refer to Removal and Installation .

NO

GO TO 6 .
INSPECT ECM AND HARNESS CONNECTOR PINS
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector E93.
3. Inspect the ECM connector pins for the following:
  - Loose connector
  - Corroded pins
  - Bent or broken pins
  - Pushed back or expanded pins
  - Moisture in or on the connector
  - Missing or damaged connector seals
  - Dirt or debris on or in the connector pins
  - Connector shell broken
  - Wire insulation damage
  - Damaged connector locking tab.
Is the inspection result normal?

YES

GO TO 7 .

NO

Repair or replace error-detected parts.
CHECK THE ECM RESPONSE
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector F101.
3. Turn ignition switch ON and wait 30 seconds.
4. Connect CONSULT and check for current "ENGINE" diagnostic trouble codes.
Did P1193-00 DTC become current?

YES

GO TO 8 .

NO

Replace ECM. Refer to Removal and Installation .
CHECK THE ECM RESPONSE
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector F101.
3. Connect a jumper wire between ECM harness connector F101 terminal 109 and 127.
4. Turn ignition switch ON and wait 30 seconds.
5. Connect CONSULT and check for current "ENGINE" diagnostic trouble codes.
Did P1192-00 DTC become current?

YES

Repair or replace engine harness.

NO

Replace ECM. Refer to Removal and Installation .