LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2021 >> NV2500 HD S >> Repair and Diagnosis >> External Pages >> Different car >> Section 162 (Seat (Circuit Diagnosis)) >> DTC/Circuit Diagnosis >> Power Supply And Ground Circuit >> Diagnosis Procedure >> RH

Diagnosis Procedure: RH

WARNING: This page is about a different car, the 2018 Nissan Titan XD and 2018 Nissan Titan. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK FUSE 

    Check if any of the following fuses are blown.

    Signal name

    Fuse No.

    Battery power supply

    60 (15A)

    IGN power supply

    29 (5A)

    Is the fuse blown?

    YES

    Replace the blown fuse after repairing the affected circuit.

    NO

    GO TO 2 .

  2. CHECK CLIMATE CONTROLLED SEAT CONTROL UNIT RH POWER SUPPLY 
    1. Turn ignition switch OFF.
    2. Disconnect climate controlled seat control unit RH connector.
    3. Turn ignition switch ON.
    4. Check voltage between climate controlled seat control unit RH harness connector B305 and ground.

      (+)

      (-)

      Voltage

      (Approx.)

      Climate controlled seat control unit RH

      Connector

      Terminal

      B305

      25

      Ground

      Battery voltage

    Is the inspection result normal?

    YES

    GO TO 7 .

    NO

    GO TO 3 .

  3. CHECK CLIMATE CONTROLLED SEAT CONTROL UNIT RH POWER SUPPLY CIRCUIT 
    1. Turn ignition switch OFF.
    2. Disconnect climate controlled seat relay.
    3. Check continuity between climate controlled seat control unit RH harness connector B305 and climate controlled seat relay harness connector M99.

      Climate controlled seat control unit RH

      Climate controlled seat relay

      Continuity

      Connector

      Terminal

      Connector

      Terminal

      B305

      25

      M99

      3

      Yes

    4. Check continuity between climate controlled seat control unit RH harness connector B305 and ground.

      Climate controlled seat control unit RH

      (-)

      Continuity

      Connector

      Terminal

      B305

      25

      Ground

      No

    Is the inspection result normal?

    YES

    GO TO 4 .

    NO

    Repair or replace harness or connector.

  4. CHECK CLIMATE CONTROLLED SEAT RELAY POWER SUPPLY CIRCUIT 
    1. Turn ignition switch ON.
    2. Check voltage between climate controlled seat relay harness connector M99 and ground.

      (+)

      (-)

      Voltage

      (Approx.)

      Climate controlled seat relay

      Connector

      Terminal

      M99

      2

      Ground

      Battery voltage

      5

    Is the inspection result normal?

    YES

    GO TO 5 .

    NO

    Repair or replace harness or connector.

  5. CHECK CLIMATE CONTROLLED SEAT RELAY GROUND CIRCUIT 
    1. Turn ignition switch OFF.
    2. Check continuity between climate controlled seat relay harness connector M99 and ground.

      Climate controlled seat relay

      (-)

      Continuity

      Connector

      Terminal

      M99

      1

      Ground

      Yes

    Is the inspection result normal?

    YES

    GO TO 6 .

    NO

    Repair or replace harness.

  6. CHECK CLIMATE CONTROLLED SEAT RELAY 

    Check climate controlled seat relay.

    Refer to Component Inspection .

    Is the inspection result normal?

    YES

    GO TO 7 .

    NO

    Replace climate controlled seat relay.

  7. CHECK CLIMATE CONTROLLED SEAT CONTROL UNIT RH GROUND CIRCUIT 
    1. Turn ignition switch OFF.
    2. Check continuity between climate controlled seat control unit RH harness connector B305 and ground.

      Climate controlled seat control unit RH

      (-)

      Continuity

      Connector

      Terminal

      B305

      27

      Ground

      Yes

    Is the inspection result normal?

    YES

    Check intermittent incident. Refer to Intermittent Incident .

    NO

    Repair harness or connector.