Diagnosis Procedure

Regarding Wiring Diagram information, refer to the appropriate Wiring Diagram .

1. CHECK CAMERA DATA MONITOR 

   Check CAMERA IMAGE SIG for each camera in "Data Monitor" of "AVM".

   Is "OK" displayed for all cameras?

   YES

   Refer to Intermittent Incident .

   NO

   GO TO 2

   NO

   GO TO 4

   NO

   GO TO 6

   NO

   GO TO 8

2. CHECK FRONT CAMERA POWER SUPPLY AND POWER SUPPLY GROUND CIRCUIT CONTINUITY 
   1. Turn ignition switch OFF.
   2. Disconnect around view monitor control unit connector B83 and front camera connector E169.
   3. Check continuity between around view monitor control unit connector B83 and front camera connector E169.

      Around view monitor control unit		Front camera		Continuity
      Connector	Terminal	Connector	Terminal
      B83	6	E169	2	Yes
      	5		1

   4. Check continuity between around view monitor control unit connector B83 and ground.

      Around view monitor control unit		Ground	Continuity
      Connector	Terminal
      B83	6	-	No

   Is the inspection result normal?

   YES

   GO TO 3 .

   NO

   Repair or replace harness or connectors.

3. CHECK AROUND VIEW MONITOR CONTROL UNIT VOLTAGE 
   1. Connect around view monitor control unit connector B83 and front camera connector E169.
   2. Turn ignition switch ON.
   3. Check voltage between around view monitor control unit connector B83 terminals.

      Around view monitor control unit B83		Condition	Voltage (Approx.)
      (+)	(-)
      Terminal	Terminal
      6	5	CAMERA switch is ON or shift position is R.	6.2 V

   Is the inspection result normal?

   YES

   Replace front camera. Refer to Removal and Installation .

   NO

   Replace around view monitor control unit. Refer to Removal and Installation .

4. CHECK REAR VIEW CAMERA POWER SUPPLY AND POWER SUPPLY GROUND CIRCUIT CONTINUITY 
   1. Turn ignition switch OFF.
   2. Disconnect around view monitor control unit connector B83 and rear view camera connector C151.
   3. Check continuity between around view monitor control unit connector B83 and rear view camera connector C151.

      Around view monitor control unit		Rear view camera		Continuity
      Connector	Terminal	Connector	Terminal
      B83	18	C151	1	Yes
      	17		2

   4. Check continuity between around view monitor control unit connector B83 and ground.

      Around view monitor control unit		Ground	Continuity
      Connector	Terminal
      B83	18	-	No

   Is the inspection result normal?

   YES

   GO TO 5 .

   NO

   Repair or replace harness or connectors.

5. CHECK AROUND VIEW MONITOR CONTROL UNIT VOLTAGE 
   1. Connect around view monitor control unit connector B83 and rear view camera connector C151.
   2. Turn ignition switch ON.
   3. Check voltage between around view monitor control unit connector B83 terminals.

      Around view monitor control unit B83		Condition	Voltage (Approx.)
      (+)	(-)
      Terminal	Terminal
      18	17	CAMERA switch is ON or shift position is R.	6.2 V

   Is the inspection result normal?

   YES

   Replace rear view camera. Refer to Removal and Installation .

   NO

   Replace around view monitor control unit. Refer to Removal and Installation .

6. CHECK LH SIDE CAMERA POWER SUPPLY AND POWER SUPPLY GROUND CIRCUIT CONTINUITY 
   1. Turn ignition switch OFF.
   2. Disconnect around view monitor control unit connector B83 and LH side camera connector D4.
   3. Check continuity between around view monitor control unit connector B83 and LH side camera connector D4.

      Around view monitor control unit		LH side camera		Continuity
      Connector	Terminal	Connector	Terminal
      B83	14	D4	7	Yes
      	13		19

   4. Check continuity between around view monitor control unit connector B83 and ground.

      Around view monitor control unit		Ground	Continuity
      Connector	Terminal
      B83	14	-	No

   Is the inspection result normal?

   YES

   GO TO 7 .

   NO

   Repair or replace harness or connectors.

7. CHECK AROUND VIEW MONITOR CONTROL UNIT VOLTAGE 
   1. Connect around view monitor control unit connector B83 and LH side camera connector D4.
   2. Turn ignition switch ON.
   3. Check voltage between around view monitor control unit connector B83 terminals.

      Around view monitor control unit B83		Condition	Voltage (Approx.)
      (+)	(-)
      Terminal	Terminal
      14	13	CAMERA switch is ON or shift position is R.	6.2 V

   Is the inspection result normal?

   YES

   Replace LH side camera. Refer to Removal and Installation .

   NO

   Replace around view monitor control unit. Refer to Removal and Installation .

8. CHECK RH SIDE CAMERA POWER SUPPLY AND POWER SUPPLY GROUND CIRCUIT CONTINUITY 
   1. Turn ignition switch OFF.
   2. Disconnect around view monitor control unit connector B83 and RH side camera connector D107.
   3. Check continuity between around view monitor control unit connector B83 and RH side camera connector D107.

      Around view monitor control unit		RH side camera		Continuity
      Connector	Terminal	Connector	Terminal
      B83	10	D107	7	Yes
      	9		19

   4. Check continuity between around view monitor control unit connector B83 and ground.

      Around view monitor control unit		Ground	Continuity
      Connector	Terminal
      B83	10	-	No

   Is the inspection result normal?

   YES

   GO TO 9 .

   NO

   Repair or replace harness or connectors.

9. CHECK AROUND VIEW MONITOR CONTROL UNIT VOLTAGE 
   1. Connect around view monitor control unit connector B83 and RH side camera connector D107.
   2. Turn ignition switch ON.
   3. Check voltage between around view monitor control unit connector B83 terminals.

      Around view monitor control unit B83		Condition	Voltage (Approx.)
      (+)	(-)
      Terminal	Terminal
      10	9	CAMERA switch is ON or shift position is R.	6.2 V

   Is the inspection result normal?

   YES

   Replace LH side camera. Refer to Removal and Installation .

   NO

   Replace around view monitor control unit. Refer to Removal and Installation .